Menu

Theme

Component reference · Component · CHECKED ON 5.0.0

Logisim input pin, output pin, probes, constants and clocks

Add a Logisim input pin (the square) to feed a value into your circuit and an output pin (the circle) to show a result; both are the Pin component, and its Type is Input or Output. Click an input pin with the Poke tool, the hand, to change its bits. Set Data Bits for a multi-bit value, use a Probe to watch any wire without adding an output, and a Constant for a fixed value.
FOR
Beginners in their first labs · Logisim-evolution 5.0.0
CHECKED
11 Nov 2026
Checked against Logisim-evolution 5.0.0 on 1 machines
On this page

Give your circuit an input

  1. Place an input pin

    Use the input pin tool in the toolbar, or open the Wiring library in the tree and choose Pin. The Type in its Properties should read Input.

    Check: A square pin with a 0 appears on the canvas.

  2. Pick the Poke tool

    The Poke tool is the active tool when a file opens in 5.0.0 (F83).

    Check: The hand tool is highlighted in the toolbar.

  3. Click the pin

    Each click toggles a 1-bit pin. Everything downstream recalculates at once.

    Check: The bit flips and the circuit reacts.

LAB lab-lnx · Linux lab5.0.02026-11-11

The half adder after one click on input A with the Poke tool: A shows 1, the sum output S shows 1 and the carry output C shows 0. A magenta ring marks the click.

One Poke click on A: A = 1, S = 1, C = 0 (F83).lab-lnx-le500-tutorial-poke-a-01
Half adder after clicking input A with the Poke tool: A and S show 1, C shows 0, a magenta ring marks the click.

Multi-bit inputs

Set Data Bits in the Properties panel. A 4-bit pin is drawn with four bit boxes, and the Radix property sets how its value is written. The window also has “Enter Decimal” and “Enter Float” dialogs for typing a value (the strings are in 5.0.0); we did not open them.

Constants, Power and Ground

A Constant has a Value, written in hex, and Data Bits. Power is always 1 and Ground always 0. Use one when an input should never change, for example a carry-in that is always 0. In our test a 4-bit Constant with value 0xA read 1010 on a 4-bit output pin, Power read 1 and Ground read 0 (F100).

circ-pins-constants · mainscroll to see all
4a4bKPoVGrG
A 4-bit constant 0xA, Power and Ground, each on an output pin. 5.0.0 read 1010, 1 and 0. CC BY 4.0 · SHA-256 a3ef5a4c10f8
Describe this circuit

Components: Constant 1; Output pin K; Power 1; Output pin V; Ground 1; Output pin G.

  • Constant 1 connects to Output pin K (net K), 4 bits wide.
  • Power 1 connects to Output pin V (net V).
  • Ground 1 connects to Output pin G (net G).

Download the circuit.

Clock

A Clock is an input that changes by itself. See Clock, ticks and simulation controls.

Buttons and switches

The Input/Output libraries have Button, DIP Switch and a Switch in the extra library; the notes list a Two-Way Switch new in 5.0.0. See the component reference.

See an output

Output pin or probe
Output pinYes, it ends a netYes, if it has a label (column per labelled pin)Radix property
ProbeNo: it reads the net it touchesNo (F100)Radix property
LEDYesNo, it is for the pictureA single bit
Hex Digit DisplayYesNoHexadecimal

Only labelled pins become columns in --tty table output and in test vectors (F05, F100). Our circuit with a probe printed just the columns A and Y:

circ-pins-probe · mainscroll to see all
AYProbeP
A NOT gate with a probe on its output. The tty table has the columns A and Y only. CC BY 4.0 · SHA-256 58696ef7ab67
Describe this circuit

Components: Input pin A; NOT Gate 1; Output pin Y; Probe P.

  • Input pin A connects to NOT Gate 1 (net A).
  • NOT Gate 1 connects to Output pin Y, Probe P (net Y).

The rows for LED and Hex Digit Display describe how they are meant to be used; we did not test them here.

Reading U, E and orange on a pin

  • U: nothing drives the net. An output pin with nothing connected read U in our test (F08, F100).
  • E: two drivers disagree (F07).
  • Orange wire, “Incompatible widths”: a 4-bit wire meets a 1-bit pin. The output pin reads U (F09, F100).
  • Grey wires and 0 on every pin right after opening a file, until one click on the canvas or Ctrl+R (F45, F49).
circ-pins-width-mismatch · mainscroll to see all
44bAY
A 4-bit input into a 1-bit output. Y reads U for all 16 values of A. CC BY 4.0 · SHA-256 25a6f9318a11
Describe this circuit

Components: Input pin A; Output pin Y.

  • Input pin A connects to Output pin Y (net A, Y), 4 bits wide.

Each of these is explained with colours in Wire colours.

Pin attributes

This is the list the Properties panel showed for a pin in 5.0.0 (F100):

LAB lab-lnx · Linux lab5.0.02026-11-11

Two Properties panels side by side. Left, an input pin named A: FPGA supported, Facing East, Type Input, Data Bits 1, Behavior Simple, Label A, Label Location West, Label Font SansSerif Bold 16, Radix Binary, Appearance Classic Logisim and Reset value 0x0. Right, an output pin named C with the same list but without Behavior and Reset value.

Properties of an input pin (left) and an output pin (right) in 5.0.0, Linux lab (F100).lab-lnx-le500-pin-properties-01
Two Properties panels side by side: an input pin A on the left and an output pin C on the right.
Pin attributes
FacingBothThe side the pin's connection faces.
TypeBothInput or Output.
Data BitsBothWidth of the value.
BehaviorInput onlySimple, Tri-state, Pull Down or Pull Up. Per the project: Simple drives what you set; Tri-state lets you set a bit to floating; the pull options replace a floating bit with 0 or 1.
Reset valueInput onlyThe value after Reset Simulation. It was 0x0 in our run.
Label, Label Location, Label FontBothThe label is the column name in test vectors.
RadixBothBinary was selected. The project lists the other radixes as octal, decimal, hexadecimal and float.
AppearanceBothClassic Logisim in our run.
FPGA supportedBothShown as a status line.

An output pin has no Behavior property. In our test, writing Pull Down or Pull Up into an output pin’s file attributes left it reading U.

Old circuits: the 4.0 pin change

Frequently asked questions

How do I change an input from 0 to 1 in Logisim?

Choose the Poke tool, the hand in the toolbar, and click the input pin. In our test, clicking input A of a half adder set A to 1 and the outputs changed at once (F83).

Why does my output pin show E, U or x?

U means nothing drives that net, E means two drivers disagree, and a 4-bit wire into a 1-bit pin also reads U. See the wire colour guide for the colours that go with each.

What is the difference between a probe and an output pin?

A probe shows the value of the wire it touches and needs no connection to anything else. An output pin ends a circuit and, with a label, appears as a column in test vectors and the tty table; a probe did not appear there (F100).

How do I make a pin 4 bits wide?

Select the pin and set Data Bits in its Properties to 4. The pin is then drawn with four bit boxes.

Why do my old circuit's inputs float after updating?

The release notes say Logisim-evolution 4.0.0 simplified pin Type and Behavior. A pin that relied on a floating value being read as 0 may need its Behavior set to Pull Down. We did not reproduce this.

Sources

  1. Logisim-evolution user guide: Pin, Probe, Constant, Logisim-evolution project, accessed 9 Nov 2026
  2. Logisim-evolution CHANGES.md, 4.0.0, GitHub, accessed 9 Nov 2026
  3. Pin and probe tests in 5.0.0, logisim.dev lab data: test-data/FINDINGS.md F83, F100; test-data/lab16-2026-11-11-pins/

Try: , , ,