PowerJava class Power, saved in files as library Wiring. | Wiring | Drives a constant 1 onto the wire it touches (supply rail symbol). | before 2.13.9 | yes | this row |
|---|
GroundJava class Ground, saved in files as library Wiring. | Wiring | Drives a constant 0 onto the wire it touches (ground symbol). | before 2.13.9 | yes | this row |
|---|
Do not connectJava class DoNotConnect, saved in files as library Wiring. | Wiring | Marks a deliberately unused output by driving a floating (Z) value. | 3.3.0 | no | this row |
|---|
TransistorJava class Transistor, saved in files as library Wiring. - drain: drain: a high source will pull drain high (only when gate is low) (out, 1 bit)
- source: source: a high source will pull drain high (only when gate is low) (in, 1 bit)
- gate: gate: when low, allows current to flow through transistor (in, 1 bit)
| Wiring | Switch-level P- or N-type MOS transistor that passes or blocks its input depending on the gate. | before 2.13.9 | yes | this row |
|---|
Transmission GateJava class TransmissionGate, saved in files as library Wiring. - drain: drain: controlled by source, depending on p-gate and n-gate (out, 1 bit)
- source: source: controls drain, depending on p-gate and n-gate (in, 1 bit)
- p-gate: p-gate: when high, allows high source to pass through to drain (in, 1 bit)
- n-gate: n-gate: when low, allows low source to pass through to drain (in, 1 bit)
| Wiring | Switch-level pass gate built from a complementary transistor pair. | before 2.13.9 | yes | this row |
|---|
Bit ExtenderJava class BitExtender, saved in files as library Wiring. - out port (out, 16 bits)
- in port (in, 8 bits)
| Wiring | Widens or narrows a value, padding with zeros, ones, the sign bit or an input bit. | before 2.13.9 | yes | this row |
|---|
SplitterJava class SplitterFactory, saved in files as library Wiring. - inout (inout, 2 bits)
- inout (inout, 1 bit)
- inout (inout, 1 bit)
| Wiring | Breaks a multi-bit bus into smaller bundles or joins bundles into a bus. | before 2.13.9 | yes | Splitter |
|---|
PinJava class Pin, saved in files as library Wiring. - Add an input pin (out, 1 bit)
| Wiring | Circuit input or output; also forms the ports of a subcircuit. | before 2.13.9 | yes | Pins, probes and constants |
|---|
ProbeJava class Probe, saved in files as library Wiring. | Wiring | Shows the value on a wire without affecting it. | before 2.13.9 | yes | Pins, probes and constants |
|---|
TunnelJava class Tunnel, saved in files as library Wiring. | Wiring | Connects wires that share the same label without drawing a wire between them. | before 2.13.9 | yes | Tunnel |
|---|
Pull ResistorJava class PullResistor, saved in files as library Wiring. | Wiring | Turns a floating value into 0, 1 or error on the attached wire. | before 2.13.9 | yes | this row |
|---|
ClockJava class Clock, saved in files as library Wiring. | Wiring | Toggles between 0 and 1 as the simulator ticks; drives sequential logic. | before 2.13.9 | yes | Pins, probes and constants |
|---|
POR (Power-on reset)Java class PowerOnReset, saved in files as library Wiring. | Wiring | Outputs a 1 for a set time after the simulation starts or restarts, then 0. | 2.14.2 | no | this row |
|---|
ConstantJava class Constant, saved in files as library Wiring. | Wiring | Outputs a fixed value of chosen width. | before 2.13.9 | yes | Pins, probes and constants |
|---|
VHDL EntityJava class VhdlEntityComponent, saved in files as library HDL-IP. - horloge_i (in, 1 bit)
- val_i (in, 4 bits)
- max_o (out, 1 bit)
- cpt_o (out, 4 bits)
| HDL-IP | Component whose interface and behaviour come from VHDL code you write (simulated through an external VHDL simulator such as Questa/ModelSim). | before 2.13.9 | no | this row |
|---|
BLIF ComponentJava class BlifCircuitComponent, saved in files as library HDL-IP. - button (in, 1 bit)
- reset (in, 1 bit)
- light_out (out, 1 bit)
| HDL-IP | Component whose logic is loaded from a BLIF (Berkeley Logic Interchange Format) netlist. | 4.0.0 | no | this row |
|---|
AdderJava class Adder, saved in files as library Arithmetic. - Input: Input: one of the numbers to add (in, 8 bits)
- Input: Input: one of the numbers to add (in, 8 bits)
- Output: Output: the sum of the inputs (plus carry in) (out, 8 bits)
- Carry In: Carry In: if 1, an additional 1 is added to output (in, 1 bit)
- Carry Out: Carry Out: 1 if the sum overflows the available bits (out, 1 bit)
| Arithmetic | Adds two binary numbers with carry in and carry out. | before 2.13.9 | yes | Adder, subtractor, comparator, shifter |
|---|
SubtractorJava class Subtractor, saved in files as library Arithmetic. - Minuend: Minuend: the number from which to subtract (in, 8 bits)
- Subtrahend: Subtrahend: the number to subtract from the minuend (in, 8 bits)
- Output: Output: the difference of the minuend and the subtrahend (out, 8 bits)
- Borrow In: Borrow In: if 1, output is decreased by 1 (in, 1 bit)
- Borrow Out: Borrow Out: 1 if the difference yields a negative value (out, 1 bit)
| Arithmetic | Subtracts two binary numbers with borrow in and borrow out. | before 2.13.9 | yes | Adder, subtractor, comparator, shifter |
|---|
MultiplierJava class Multiplier, saved in files as library Arithmetic. - Input: Input: one of the numbers to multiply (in, 8 bits)
- Input: Input: one of the numbers to multiply (in, 8 bits)
- Output: Output: the product of the inputs, plus the carry in (out, 8 bits)
- Carry In: Carry In: an amount to be added into the output (in, 8 bits)
- Carry Out: Carry Out: the upper bits of the product (out, 8 bits)
| Arithmetic | Multiplies two numbers (signed/unsigned option added in 5.0.0). | before 2.13.9 | yes | Adder, subtractor, comparator, shifter |
|---|
DividerJava class Divider, saved in files as library Arithmetic. - Dividend Lower: Dividend Lower: the lower half of the number to divide (in, 8 bits)
- Divisor: Divisor: the number by which to divide (in, 8 bits)
- Output: Output: the result of dividing the dividend by the divisor (out, 8 bits)
- Dividend Upper: Dividend Upper: the upper half of the number to divide (in, 8 bits)
- Remainder: Remainder: the remainder (dividend - output * divisor) (out, 8 bits)
| Arithmetic | Divides two numbers, giving quotient and remainder. | before 2.13.9 | yes | Adder, subtractor, comparator, shifter |
|---|
NegatorJava class Negator, saved in files as library Arithmetic. - Input: Input: the number to be negated (in, 8 bits)
- Output: Output: the two’s-complement negation of the input (out, 8 bits)
| Arithmetic | Outputs the two's-complement negation of its input. | before 2.13.9 | yes | Adder, subtractor, comparator, shifter |
|---|
ExponentiatorJava class Exponentiator, saved in files as library Arithmetic. - Base: Base: the number to be raised to a power (in, 32 bits)
- Exponent: Exponent: the power to which the base is raised (in, 32 bits)
- Lower Output: Lower Output: the lower bits of the exponentiation result (out, 32 bits)
- Upper Output: Upper Output: the upper bits of the exponentiation result (out, 32 bits)
| Arithmetic | Raises one integer input to the power of another. | 4.1.0 | no | Adder, subtractor, comparator, shifter |
|---|
Square RootJava class SquareRoot, saved in files as library Arithmetic. - Lower Radicand: Lower Radicand: the lower half of the number to be square rooted (in, 8 bits)
- Output: Output: the result of the square root (out, 8 bits)
- Upper Radicand: Upper Radicand: the upper half of the number to be square rooted (in, 8 bits)
- Remainder: Remainder: the remainder (radicand - output * output) (out, 8 bits)
| Arithmetic | Computes the integer square root of its input. | 4.1.0 | no | Adder, subtractor, comparator, shifter |
|---|
AbsoluteJava class Absolute, saved in files as library Arithmetic. - Input: Input: the number whose absolute value will be calculated (in, 8 bits)
- Output: Output: the absolute (positive) value of the input (out, 8 bits)
- Overflow: Overflow: activates when the input is at the minimum possible value (out, 1 bit)
| Arithmetic | Outputs the absolute value of a signed integer. | 4.1.0 | no | Adder, subtractor, comparator, shifter |
|---|
ComparatorJava class Comparator, saved in files as library Arithmetic. - A: A: the number preceding the comparison operation (in, 8 bits)
- B: B: the number following the comparison operation (in, 8 bits)
- Greater: Greater: 1 if A is greater than B (out, 1 bit)
- Equal: Equal: 1 if A is equal to B (out, 1 bit)
- Less: Less: 1 if A is less than B (out, 1 bit)
| Arithmetic | Compares two numbers and signals less than, equal or greater than. | before 2.13.9 | yes | Adder, subtractor, comparator, shifter |
|---|
Minimum and MaximumJava class MinMax, saved in files as library Arithmetic. - Input: Input: one of the numbers to test for minimum and maximum (in, 8 bits)
- Input: Input: one of the numbers to test for minimum and maximum (in, 8 bits)
- Min Output: Min Output: the minimum value between the two inputs (out, 8 bits)
- Max Output: Max Output: the maximum value between the two inputs (out, 8 bits)
| Arithmetic | Outputs the smaller or larger of its inputs. | 4.1.0 | no | Adder, subtractor, comparator, shifter |
|---|
ShifterJava class Shifter, saved in files as library Arithmetic. - Input: Input: bits to be shifted (in, 8 bits)
- Distance: Distance: how far to shift the input (in, 3 bits)
- Output: Output: result of shifting the input (out, 8 bits)
| Arithmetic | Shifts or rotates a value left or right by a given amount. | before 2.13.9 | yes | Adder, subtractor, comparator, shifter |
|---|
Bit AdderJava class BitAdder, saved in files as library Arithmetic. - Output: Output: how many input bits are 1 (out, 4 bits)
- Input: Input: the bits to be counted (in, 8 bits)
| Arithmetic | Counts how many input bits are 1. | before 2.13.9 | yes | Adder, subtractor, comparator, shifter |
|---|
Bit FinderJava class BitFinder, saved in files as library Arithmetic. - Present: Present: 1 if input contains a 1 (out, 1 bit)
- Index: Index: index of input’s lowest-order 1 (out, 3 bits)
- Input: Input: the bits to be searched (in, 8 bits)
| Arithmetic | Finds the position of the lowest or highest 0 or 1 bit. | before 2.13.9 | yes | Adder, subtractor, comparator, shifter |
|---|
Floating Point ConstantJava class FpConstant, saved in files as library FPArithmetic. - Output: Output: the encoded floating point constant (out, 32 bits)
| Floating Point Arithmetic | Outputs a fixed IEEE floating-point value. | 5.0.0 | new in 5.0.0 | this row |
|---|
Floating Point AdderJava class FpAdder, saved in files as library FPArithmetic. - Input: Input: one of the numbers to add (in, 32 bits)
- Input: Input: one of the numbers to add (in, 32 bits)
- Output: Output: the sum of the inputs (out, 32 bits)
- Error: Error: 1 if input or output is NaN (out, 1 bit)
| Floating Point Arithmetic | Adds two IEEE floating-point numbers. | 3.6.0 | no | this row |
|---|
Floating Point SubtractorJava class FpSubtractor, saved in files as library FPArithmetic. - Minuend: Minuend: the number from which to subtract (in, 32 bits)
- Subtrahend: Subtrahend: the number to subtract from the minuend (in, 32 bits)
- Output: Output: the difference of the minuend and the subtrahend (out, 32 bits)
- Error: Error: 1 if input or output is NaN (out, 1 bit)
| Floating Point Arithmetic | Subtracts two IEEE floating-point numbers. | 3.6.0 | no | this row |
|---|
Floating Point MultiplierJava class FpMultiplier, saved in files as library FPArithmetic. - Input: Input: one of the numbers to multiply (in, 32 bits)
- Input: Input: one of the numbers to multiply (in, 32 bits)
- Output: Output: the product of the inputs (out, 32 bits)
- Error: Error: 1 if input or output is NaN (out, 1 bit)
| Floating Point Arithmetic | Multiplies two IEEE floating-point numbers. | 3.6.0 | no | this row |
|---|
Floating Point DividerJava class FpDivider, saved in files as library FPArithmetic. - Dividend: Dividend: the number to divide (in, 32 bits)
- Divisor: Divisor: the number by which to divide (in, 32 bits)
- Output: Output: the result of dividing the dividend by the divisor (out, 32 bits)
- Remainder: Remainder: the remainder (dividend - output * divisor) (out, 32 bits)
- Error: Error: 1 if input or output is NaN (out, 1 bit)
| Floating Point Arithmetic | Divides two IEEE floating-point numbers. | 3.6.0 | no | this row |
|---|
Floating Point NegatorJava class FpNegator, saved in files as library FPArithmetic. - Input: Input: the number to be negated (in, 32 bits)
- Negation of the input (out, 32 bits)
- Error: Error: 1 if input or output is NaN (out, 1 bit)
| Floating Point Arithmetic | Flips the sign of an IEEE floating-point number. | 3.6.0 | no | this row |
|---|
Floating Point ExponentiatorJava class FpExponentiator, saved in files as library FPArithmetic. - Exponent: Exponent: the power to which the base is raised (in, 32 bits)
- Output: Output: the exponentiation result (out, 32 bits)
- Error: Error: 1 if input or output is NaN (out, 1 bit)
- Base: Base: the number to be raised to a power (in, 32 bits)
| Floating Point Arithmetic | Raises a floating-point value to a power. | 4.1.0 | no | this row |
|---|
Floating Point LogarithmJava class FpLogarithm, saved in files as library FPArithmetic. - Anti-logarithm: Anti-logarithm: the value obtained by raising the base to the given power (in, 32 bits)
- Output: Output: the result of the logarithm (out, 32 bits)
- Error: Error: 1 if input or output is NaN (out, 1 bit)
- Base: Base: the base of the logarithm (in, 32 bits)
| Floating Point Arithmetic | Computes a logarithm of a floating-point value. | 4.1.0 | no | this row |
|---|
Floating Point Square RootJava class FpSquareRoot, saved in files as library FPArithmetic. - Input: Input: the number to be square rooted (in, 32 bits)
- Output: Output: the result of the square root (out, 32 bits)
- Error: Error: 1 if input or output is NaN (out, 1 bit)
| Floating Point Arithmetic | Square root of a floating-point value. | 4.1.0 | no | this row |
|---|
Floating Point AbsoluteJava class FpAbsolute, saved in files as library FPArithmetic. - Input: Input: the number whose absolute value will be calculated (in, 32 bits)
- Output: Output: the absolute (positive) value of the input (out, 32 bits)
- Error: Error: 1 if input or output is NaN (out, 1 bit)
| Floating Point Arithmetic | Absolute value of a floating-point number. | 4.1.0 | no | this row |
|---|
Floating Point ComparatorJava class FpComparator, saved in files as library FPArithmetic. - A: A: the number preceding the comparison operation (in, 32 bits)
- B: B: the number following the comparison operation (in, 32 bits)
- Greater: Greater: 1 if A is greater than B (out, 1 bit)
- Equal: Equal: 1 if A is equal to B (out, 1 bit)
- Less: Less: 1 if A is less than B (out, 1 bit)
- Error: Error: 1 if input or output is NaN (out, 1 bit)
| Floating Point Arithmetic | Compares two floating-point numbers. | 3.6.0 | no | this row |
|---|
Floating Point Minimum and MaximumJava class FpMinMax, saved in files as library FPArithmetic. - Input: Input: one of the numbers to test for minimum and maximum (in, 32 bits)
- Input: Input: one of the numbers to test for minimum and maximum (in, 32 bits)
- Min Output: Min Output: the minimum value between the two inputs (out, 32 bits)
- Max Output: Max Output: the maximum value between the two inputs (out, 32 bits)
- Error: Error: 1 if input or output is NaN (out, 1 bit)
| Floating Point Arithmetic | Smaller or larger of floating-point inputs. | 4.1.0 | no | this row |
|---|
Floating Point RoundJava class FpRound, saved in files as library FPArithmetic. - Input: Input: the number to be rounded (in, 32 bits)
- Output: Output: the rounded value of the input (out, 32 bits)
- Error: Error: 1 if input or output is NaN (out, 1 bit)
| Floating Point Arithmetic | Rounds a floating-point value (e.g. floor, ceiling, nearest). | 4.1.0 | no | this row |
|---|
Floating Point TrigonometryJava class FpTrigonometry, saved in files as library FPArithmetic. - Input: Input: the value to be processed by the trigonometric functions (in, 32 bits)
- Sine: Sine: the corresponding result of the sine function for the selected type (out, 32 bits)
- Tangent: Tangent: the ratio between the sine and cosine outputs (out, 32 bits)
- Cosine: Cosine: the corresponding result of the cosine function for the selected type (out, 32 bits)
- Error: Error: 1 if input or output is NaN (out, 1 bit)
| Floating Point Arithmetic | Sine, cosine and related functions on floating-point values. | 4.1.0 | no | this row |
|---|
Floating Point ClassificatorJava class FpClassificator, saved in files as library FPArithmetic. - Input: Input: the floating point number to be classified (in, 32 bits)
- Enables when the value is negative (out, 1 bit)
- Enables when the value's magnitude is zero (out, 1 bit)
- Enables when the exponent is zero and the fraction is non‑zero (out, 1 bit)
- Enables when the exponent is greater than zero and less than its maximum value (out, 1 bit)
- Enables when the value is infinite (out, 1 bit)
- Enables when the value is not a number (out, 1 bit)
| Floating Point Arithmetic | Reports whether a floating-point value is zero, infinite, NaN, negative and so on. | 4.1.0 | no | this row |
|---|
Floating Point ConverterJava class FpToFp, saved in files as library FPArithmetic. - Input: Input: the float number to be converted (in, 32 bits)
- Output: Output: the converted float number (out, 32 bits)
- Error: Error: 1 if input or output is NaN (out, 1 bit)
| Floating Point Arithmetic | Converts between floating-point formats (16/32/64-bit). | 4.1.0 | no | this row |
|---|
Floating Point to IntegerJava class FpToInt, saved in files as library FPArithmetic. - Input: Input: the floating point value to convert (in, 32 bits)
- Output: Output: signed output containing the rounded floating point value (out, 8 bits)
- Error: Error: 1 if input or output is NaN (out, 1 bit)
| Floating Point Arithmetic | Converts a floating-point value to an integer. | 3.6.0 | no | this row |
|---|
Integer to Floating PointJava class IntToFp, saved in files as library FPArithmetic. - Input: Input: the integer to convert to floating point (in, 8 bits)
- Output: Output: the floating point form of the input (out, 32 bits)
- Error: Error: 1 if input or output is NaN (out, 1 bit)
| Floating Point Arithmetic | Converts an integer to a floating-point value. | 3.6.0 | no | this row |
|---|
7400: quad 2-input NAND gateJava class Ttl7400, saved in files as library TTL. - Input: Input : 1 (in, 1 bit)
- Input: Input : 2 (in, 1 bit)
- Output: Output : 3 (out, 1 bit)
- Input: Input : 4 (in, 1 bit)
- Input: Input : 5 (in, 1 bit)
- Output: Output : 6 (out, 1 bit)
- Output: Output : 8 (out, 1 bit)
- Input: Input : 9 (in, 1 bit)
- Input: Input : 10 (in, 1 bit)
- Output: Output : 11 (out, 1 bit)
- Input: Input : 12 (in, 1 bit)
- Input: Input : 13 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7400: quad 2-input NAND gate | 2.15.0 | no | TTL 7400-series library |
|---|
7402: quad 2-input NOR gate (right-to-left)Java class Ttl7402, saved in files as library TTL. - Output: Output : 1 (out, 1 bit)
- Input: Input : 2 (in, 1 bit)
- Input: Input : 3 (in, 1 bit)
- Output: Output : 4 (out, 1 bit)
- Input: Input : 5 (in, 1 bit)
- Input: Input : 6 (in, 1 bit)
- Input: Input : 8 (in, 1 bit)
- Input: Input : 9 (in, 1 bit)
- Output: Output : 10 (out, 1 bit)
- Input: Input : 11 (in, 1 bit)
- Input: Input : 12 (in, 1 bit)
- Output: Output : 13 (out, 1 bit)
| TTL | Model of the 74-series TTL chip 7402: quad 2-input NOR gate (right-to-left) | 2.15.0 | no | TTL 7400-series library |
|---|
7404: hex inverterJava class Ttl7404, saved in files as library TTL. - Input: Input : 1 (in, 1 bit)
- Output: Output : 2 (out, 1 bit)
- Input: Input : 3 (in, 1 bit)
- Output: Output : 4 (out, 1 bit)
- Input: Input : 5 (in, 1 bit)
- Output: Output : 6 (out, 1 bit)
- Output: Output : 8 (out, 1 bit)
- Input: Input : 9 (in, 1 bit)
- Output: Output : 10 (out, 1 bit)
- Input: Input : 11 (in, 1 bit)
- Output: Output : 12 (out, 1 bit)
- Input: Input : 13 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7404: hex inverter | 2.15.0 | no | TTL 7400-series library |
|---|
7408: quad 2-input AND gateJava class Ttl7408, saved in files as library TTL. - Input: Input : 1 (in, 1 bit)
- Input: Input : 2 (in, 1 bit)
- Output: Output : 3 (out, 1 bit)
- Input: Input : 4 (in, 1 bit)
- Input: Input : 5 (in, 1 bit)
- Output: Output : 6 (out, 1 bit)
- Output: Output : 8 (out, 1 bit)
- Input: Input : 9 (in, 1 bit)
- Input: Input : 10 (in, 1 bit)
- Output: Output : 11 (out, 1 bit)
- Input: Input : 12 (in, 1 bit)
- Input: Input : 13 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7408: quad 2-input AND gate | 2.15.0 | no | TTL 7400-series library |
|---|
7410: triple 3-input NAND gateJava class Ttl7410, saved in files as library TTL. - Input: Input : 1 (in, 1 bit)
- Input: Input : 2 (in, 1 bit)
- Input: Input : 3 (in, 1 bit)
- Input: Input : 4 (in, 1 bit)
- Input: Input : 5 (in, 1 bit)
- Output: Output : 6 (out, 1 bit)
- Output: Output : 8 (out, 1 bit)
- Input: Input : 9 (in, 1 bit)
- Input: Input : 10 (in, 1 bit)
- Input: Input : 11 (in, 1 bit)
- Output: Output : 12 (out, 1 bit)
- Input: Input : 13 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7410: triple 3-input NAND gate | 2.15.0 | no | TTL 7400-series library |
|---|
7411: triple 3-input AND gateJava class Ttl7411, saved in files as library TTL. - Input: Input : 1 (in, 1 bit)
- Input: Input : 2 (in, 1 bit)
- Input: Input : 3 (in, 1 bit)
- Input: Input : 4 (in, 1 bit)
- Input: Input : 5 (in, 1 bit)
- Output: Output : 6 (out, 1 bit)
- Output: Output : 8 (out, 1 bit)
- Input: Input : 9 (in, 1 bit)
- Input: Input : 10 (in, 1 bit)
- Input: Input : 11 (in, 1 bit)
- Output: Output : 12 (out, 1 bit)
- Input: Input : 13 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7411: triple 3-input AND gate | 2.15.0 | no | TTL 7400-series library |
|---|
7413: dual 4-input NAND gate(Schmitt trigger)Java class Ttl7413, saved in files as library TTL. - Input 1: Input 1: A0 (in, 1 bit)
- Input 2: Input 2: B0 (in, 1 bit)
- Input 4: Input 4: C0 (in, 1 bit)
- Input 5: Input 5: D0 (in, 1 bit)
- Output 6: Output 6: Y0 (out, 1 bit)
- Output 8: Output 8: Y1 (out, 1 bit)
- Input 9: Input 9: D1 (in, 1 bit)
- Input 10: Input 10: C1 (in, 1 bit)
- Input 12: Input 12: B1 (in, 1 bit)
- Input 13: Input 13: A1 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7413: dual 4-input NAND gate(Schmitt trigger) | 2.15.0 | no | TTL 7400-series library |
|---|
7414: hex inverter (Schmitt trigger)Java class Ttl7414, saved in files as library TTL. - Input: Input : 1 (in, 1 bit)
- Output: Output : 2 (out, 1 bit)
- Input: Input : 3 (in, 1 bit)
- Output: Output : 4 (out, 1 bit)
- Input: Input : 5 (in, 1 bit)
- Output: Output : 6 (out, 1 bit)
- Output: Output : 8 (out, 1 bit)
- Input: Input : 9 (in, 1 bit)
- Output: Output : 10 (out, 1 bit)
- Input: Input : 11 (in, 1 bit)
- Output: Output : 12 (out, 1 bit)
- Input: Input : 13 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7414: hex inverter (Schmitt trigger) | 2.15.0 | no | TTL 7400-series library |
|---|
7418: dual 4-input NAND gate(Schmitt trigger)Java class Ttl7418, saved in files as library TTL. - Input 1: Input 1: A0 (in, 1 bit)
- Input 2: Input 2: B0 (in, 1 bit)
- Input 4: Input 4: C0 (in, 1 bit)
- Input 5: Input 5: D0 (in, 1 bit)
- Output 6: Output 6: Y0 (out, 1 bit)
- Output 8: Output 8: Y1 (out, 1 bit)
- Input 9: Input 9: D1 (in, 1 bit)
- Input 10: Input 10: C1 (in, 1 bit)
- Input 12: Input 12: B1 (in, 1 bit)
- Input 13: Input 13: A1 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7418: dual 4-input NAND gate(Schmitt trigger) | 2.15.0 | no | TTL 7400-series library |
|---|
7419: hex inverter (Schmitt trigger)Java class Ttl7419, saved in files as library TTL. - Input: Input : 1 (in, 1 bit)
- Output: Output : 2 (out, 1 bit)
- Input: Input : 3 (in, 1 bit)
- Output: Output : 4 (out, 1 bit)
- Input: Input : 5 (in, 1 bit)
- Output: Output : 6 (out, 1 bit)
- Output: Output : 8 (out, 1 bit)
- Input: Input : 9 (in, 1 bit)
- Output: Output : 10 (out, 1 bit)
- Input: Input : 11 (in, 1 bit)
- Output: Output : 12 (out, 1 bit)
- Input: Input : 13 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7419: hex inverter (Schmitt trigger) | 2.15.0 | no | TTL 7400-series library |
|---|
7420: dual 4-input NAND gateJava class Ttl7420, saved in files as library TTL. - Input 1: Input 1: A0 (in, 1 bit)
- Input 2: Input 2: B0 (in, 1 bit)
- Input 4: Input 4: C0 (in, 1 bit)
- Input 5: Input 5: D0 (in, 1 bit)
- Output 6: Output 6: Y0 (out, 1 bit)
- Output 8: Output 8: Y1 (out, 1 bit)
- Input 9: Input 9: D1 (in, 1 bit)
- Input 10: Input 10: C1 (in, 1 bit)
- Input 12: Input 12: B1 (in, 1 bit)
- Input 13: Input 13: A1 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7420: dual 4-input NAND gate | 2.15.0 | no | TTL 7400-series library |
|---|
7421: dual 4-input AND gateJava class Ttl7421, saved in files as library TTL. - Input 1: Input 1: A0 (in, 1 bit)
- Input 2: Input 2: B0 (in, 1 bit)
- Input 4: Input 4: C0 (in, 1 bit)
- Input 5: Input 5: D0 (in, 1 bit)
- Output 6: Output 6: Y0 (out, 1 bit)
- Output 8: Output 8: Y1 (out, 1 bit)
- Input 9: Input 9: D1 (in, 1 bit)
- Input 10: Input 10: C1 (in, 1 bit)
- Input 12: Input 12: B1 (in, 1 bit)
- Input 13: Input 13: A1 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7421: dual 4-input AND gate | 2.15.0 | no | TTL 7400-series library |
|---|
7424: quad 2-input NAND gate (Schmitt trigger)Java class Ttl7424, saved in files as library TTL. - Input: Input : 1 (in, 1 bit)
- Input: Input : 2 (in, 1 bit)
- Output: Output : 3 (out, 1 bit)
- Input: Input : 4 (in, 1 bit)
- Input: Input : 5 (in, 1 bit)
- Output: Output : 6 (out, 1 bit)
- Output: Output : 8 (out, 1 bit)
- Input: Input : 9 (in, 1 bit)
- Input: Input : 10 (in, 1 bit)
- Output: Output : 11 (out, 1 bit)
- Input: Input : 12 (in, 1 bit)
- Input: Input : 13 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7424: quad 2-input NAND gate (Schmitt trigger) | 2.15.0 | no | TTL 7400-series library |
|---|
7427: triple 3-input NOR gateJava class Ttl7427, saved in files as library TTL. - Input: Input : 1 (in, 1 bit)
- Input: Input : 2 (in, 1 bit)
- Input: Input : 3 (in, 1 bit)
- Input: Input : 4 (in, 1 bit)
- Input: Input : 5 (in, 1 bit)
- Output: Output : 6 (out, 1 bit)
- Output: Output : 8 (out, 1 bit)
- Input: Input : 9 (in, 1 bit)
- Input: Input : 10 (in, 1 bit)
- Input: Input : 11 (in, 1 bit)
- Output: Output : 12 (out, 1 bit)
- Input: Input : 13 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7427: triple 3-input NOR gate | 2.15.0 | no | TTL 7400-series library |
|---|
7430: single 8-input NAND gateJava class Ttl7430, saved in files as library TTL. - Input 1: Input 1: A (in, 1 bit)
- Input 2: Input 2: B (in, 1 bit)
- Input 3: Input 3: C (in, 1 bit)
- Input 4: Input 4: D (in, 1 bit)
- Input 5: Input 5: E (in, 1 bit)
- Input 6: Input 6: F (in, 1 bit)
- Output 8: Output 8: Y (out, 1 bit)
- Input 11: Input 11: G (in, 1 bit)
- Input 12: Input 12: H (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7430: single 8-input NAND gate | 2.15.0 | no | TTL 7400-series library |
|---|
7432: quad 2-input OR gateJava class Ttl7432, saved in files as library TTL. - Input: Input : 1 (in, 1 bit)
- Input: Input : 2 (in, 1 bit)
- Output: Output : 3 (out, 1 bit)
- Input: Input : 4 (in, 1 bit)
- Input: Input : 5 (in, 1 bit)
- Output: Output : 6 (out, 1 bit)
- Output: Output : 8 (out, 1 bit)
- Input: Input : 9 (in, 1 bit)
- Input: Input : 10 (in, 1 bit)
- Output: Output : 11 (out, 1 bit)
- Input: Input : 12 (in, 1 bit)
- Input: Input : 13 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7432: quad 2-input OR gate | 2.15.0 | no | TTL 7400-series library |
|---|
7434: hex buffer gateJava class Ttl7434, saved in files as library TTL. - Input: Input : 1 (in, 1 bit)
- Output: Output : 2 (out, 1 bit)
- Input: Input : 3 (in, 1 bit)
- Output: Output : 4 (out, 1 bit)
- Input: Input : 5 (in, 1 bit)
- Output: Output : 6 (out, 1 bit)
- Output: Output : 8 (out, 1 bit)
- Input: Input : 9 (in, 1 bit)
- Output: Output : 10 (out, 1 bit)
- Input: Input : 11 (in, 1 bit)
- Output: Output : 12 (out, 1 bit)
- Input: Input : 13 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7434: hex buffer gate | 3.6.0 | no | TTL 7400-series library |
|---|
7436: quad 2-input NOR gateJava class Ttl7436, saved in files as library TTL. - Input: Input : 1 (in, 1 bit)
- Input: Input : 2 (in, 1 bit)
- Output: Output : 3 (out, 1 bit)
- Input: Input : 4 (in, 1 bit)
- Input: Input : 5 (in, 1 bit)
- Output: Output : 6 (out, 1 bit)
- Output: Output : 8 (out, 1 bit)
- Input: Input : 9 (in, 1 bit)
- Input: Input : 10 (in, 1 bit)
- Output: Output : 11 (out, 1 bit)
- Input: Input : 12 (in, 1 bit)
- Input: Input : 13 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7436: quad 2-input NOR gate | 2.15.0 | no | TTL 7400-series library |
|---|
7438: quad 2-input NAND gate (open-collector)Java class Ttl7438, saved in files as library TTL. - Input 1: Input 1: 1A (in, 1 bit)
- Input 2: Input 2: 1B (in, 1 bit)
- Output 3: Output 3: 1Y (out, 1 bit)
- Input 4: Input 4: 2A (in, 1 bit)
- Input 5: Input 5: 2B (in, 1 bit)
- Output 6: Output 6: 2Y (out, 1 bit)
- Output 8: Output 8: 3Y (out, 1 bit)
- Input 9: Input 9: 3A (in, 1 bit)
- Input 10: Input 10: 3B (in, 1 bit)
- Output 11: Output 11: 4Y (out, 1 bit)
- Input 12: Input 12: 4A (in, 1 bit)
- Input 13: Input 13: 4B (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7438: quad 2-input NAND gate (open-collector) | 5.0.0 | new in 5.0.0 | TTL 7400-series library |
|---|
7442: BCD to decimal decoderJava class Ttl7442, saved in files as library TTL. - Output 1: Output 1: O0 (out, 1 bit)
- Output 2: Output 2: O1 (out, 1 bit)
- Output 3: Output 3: O2 (out, 1 bit)
- Output 4: Output 4: O3 (out, 1 bit)
- Output 5: Output 5: O4 (out, 1 bit)
- Output 6: Output 6: O5 (out, 1 bit)
- Output 7: Output 7: O6 (out, 1 bit)
- Output 9: Output 9: O7 (out, 1 bit)
- Output 10: Output 10: O8 (out, 1 bit)
- Output 11: Output 11: O9 (out, 1 bit)
- Input 12: Input 12: D (in, 1 bit)
- Input 13: Input 13: C (in, 1 bit)
- Input 14: Input 14: B (in, 1 bit)
- Input 15: Input 15: A (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7442: BCD to decimal decoder | 2.15.0 | no | TTL 7400-series library |
|---|
7443: Excess-3 to decimal decoderJava class Ttl7443, saved in files as library TTL. - Output 1: Output 1: O0 (out, 1 bit)
- Output 2: Output 2: O1 (out, 1 bit)
- Output 3: Output 3: O2 (out, 1 bit)
- Output 4: Output 4: O3 (out, 1 bit)
- Output 5: Output 5: O4 (out, 1 bit)
- Output 6: Output 6: O5 (out, 1 bit)
- Output 7: Output 7: O6 (out, 1 bit)
- Output 9: Output 9: O7 (out, 1 bit)
- Output 10: Output 10: O8 (out, 1 bit)
- Output 11: Output 11: O9 (out, 1 bit)
- Input 12: Input 12: D (in, 1 bit)
- Input 13: Input 13: C (in, 1 bit)
- Input 14: Input 14: B (in, 1 bit)
- Input 15: Input 15: A (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7443: Excess-3 to decimal decoder | 2.15.0 | no | TTL 7400-series library |
|---|
7444: Gray to decimal decoderJava class Ttl7444, saved in files as library TTL. - Output 1: Output 1: O0 (out, 1 bit)
- Output 2: Output 2: O1 (out, 1 bit)
- Output 3: Output 3: O2 (out, 1 bit)
- Output 4: Output 4: O3 (out, 1 bit)
- Output 5: Output 5: O4 (out, 1 bit)
- Output 6: Output 6: O5 (out, 1 bit)
- Output 7: Output 7: O6 (out, 1 bit)
- Output 9: Output 9: O7 (out, 1 bit)
- Output 10: Output 10: O8 (out, 1 bit)
- Output 11: Output 11: O9 (out, 1 bit)
- Input 12: Input 12: D (in, 1 bit)
- Input 13: Input 13: C (in, 1 bit)
- Input 14: Input 14: B (in, 1 bit)
- Input 15: Input 15: A (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7444: Gray to decimal decoder | 2.15.0 | no | TTL 7400-series library |
|---|
7447: BCD to 7-segment decoderJava class Ttl7447, saved in files as library TTL. - Input 1: Input 1: B (in, 1 bit)
- Input 2: Input 2: C (in, 1 bit)
- Input 3: Input 3: LT (in, 1 bit)
- Input/Output 4: Input/Output 4: BI/RBO (inout, 1 bit)
- Input 5: Input 5: RBI (in, 1 bit)
- Input 6: Input 6: D (in, 1 bit)
- Input 7: Input 7: A (in, 1 bit)
- Output 9: Output 9: e (out, 1 bit)
- Output 10: Output 10: d (out, 1 bit)
- Output 11: Output 11: c (out, 1 bit)
- Output 12: Output 12: b (out, 1 bit)
- Output 13: Output 13: a (out, 1 bit)
- Output 14: Output 14: g (out, 1 bit)
- Output 15: Output 15: f (out, 1 bit)
| TTL | Model of the 74-series TTL chip 7447: BCD to 7-segment decoder | 2.15.0 | no | TTL 7400-series library |
|---|
7451: dual AND-OR-INVERT gateJava class Ttl7451, saved in files as library TTL. - Input 1: Input 1: A1 (in, 1 bit)
- Input 2: Input 2: A2 (in, 1 bit)
- Input 3: Input 3: B2 (in, 1 bit)
- Input 4: Input 4: C2 (in, 1 bit)
- Input 5: Input 5: D2 (in, 1 bit)
- Output 6: Output 6: Y2 (out, 1 bit)
- Output 8: Output 8: Y1 (out, 1 bit)
- Input 9: Input 9: C1 (in, 1 bit)
- Input 10: Input 10: D1 (in, 1 bit)
- Input 13: Input 13: B1 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7451: dual AND-OR-INVERT gate | 2.15.0 | no | TTL 7400-series library |
|---|
7454: Four wide AND-OR-INVERT gateJava class Ttl7454, saved in files as library TTL. - Input 1: Input 1: A (in, 1 bit)
- Input 2: Input 2: C (in, 1 bit)
- Input 3: Input 3: D (in, 1 bit)
- Input 4: Input 4: E (in, 1 bit)
- Input 5: Input 5: F (in, 1 bit)
- Output 8: Output 8: Y (out, 1 bit)
- Input 9: Input 9: G (in, 1 bit)
- Input 10: Input 10: H (in, 1 bit)
- Input 13: Input 13: B (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7454: Four wide AND-OR-INVERT gate | 2.15.0 | no | TTL 7400-series library |
|---|
7458: dual AND-OR gateJava class Ttl7458, saved in files as library TTL. - Input 1: Input 1: A0 (in, 1 bit)
- Input 2: Input 2: A1 (in, 1 bit)
- Input 3: Input 3: B1 (in, 1 bit)
- Input 4: Input 4: C1 (in, 1 bit)
- Input 5: Input 5: D1 (in, 1 bit)
- Output 6: Output 6: Y1 (out, 1 bit)
- Output 8: Output 8: Y0 (out, 1 bit)
- Input 9: Input 9: D0 (in, 1 bit)
- Input 10: Input 10: E0 (in, 1 bit)
- Input 11: Input 11: F0 (in, 1 bit)
- Input 12: Input 12: B0 (in, 1 bit)
- Input 13: Input 13: C0 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7458: dual AND-OR gate | 2.15.0 | no | TTL 7400-series library |
|---|
7464: 4-2-3-2 AND-OR-INVERT gateJava class Ttl7464, saved in files as library TTL. - Input 1: Input 1: A (in, 1 bit)
- Input 2: Input 2: E (in, 1 bit)
- Input 3: Input 3: F (in, 1 bit)
- Input 4: Input 4: G (in, 1 bit)
- Input 5: Input 5: H (in, 1 bit)
- Input 6: Input 6: I (in, 1 bit)
- Output 8: Output 8: Y (out, 1 bit)
- Input 9: Input 9: J (in, 1 bit)
- Input 10: Input 10: K (in, 1 bit)
- Input 11: Input 11: B (in, 1 bit)
- Input 12: Input 12: C (in, 1 bit)
- Input 13: Input 13: D (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7464: 4-2-3-2 AND-OR-INVERT gate | 2.15.0 | no | TTL 7400-series library |
|---|
7474: dual D-Flipflops with preset and clearJava class Ttl7474, saved in files as library TTL. - Input 1: Input 1: nCLR1 (in, 1 bit)
- Input 2: Input 2: D1 (in, 1 bit)
- Input 3: Input 3: CLK1 (in, 1 bit)
- Input 4: Input 4: nPRE1 (in, 1 bit)
- Output 5: Output 5: Q1 (out, 1 bit)
- Output 6: Output 6: nQ1 (out, 1 bit)
- Output 8: Output 8: nQ2 (out, 1 bit)
- Output 9: Output 9: Q2 (out, 1 bit)
- Input 10: Input 10: nPRE2 (in, 1 bit)
- Input 11: Input 11: CLK2 (in, 1 bit)
- Input 12: Input 12: D2 (in, 1 bit)
- Input 13: Input 13: nCLR2 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7474: dual D-Flipflops with preset and clear | 2.15.0 | no | TTL 7400-series library |
|---|
7476: dual J-K Flipflops with preset and clearJava class Ttl7476, saved in files as library TTL. - Input 1: Input 1: CLK1 (in, 1 bit)
- Input 2: Input 2: nPRE1 (in, 1 bit)
- Input 3: Input 3: nCLR1 (in, 1 bit)
- Input 4: Input 4: J1 (in, 1 bit)
- Input 5: Input 5: CLK2 (in, 1 bit)
- Input 6: Input 6: nPRE2 (in, 1 bit)
- Input 7: Input 7: nCLR2 (in, 1 bit)
- Input 9: Input 9: J2 (in, 1 bit)
- Output 10: Output 10: nQ2 (out, 1 bit)
- Output 11: Output 11: Q2 (out, 1 bit)
- Input 12: Input 12: K2 (in, 1 bit)
- Output 13: Output 13: nQ1 (out, 1 bit)
- Output 14: Output 14: Q1 (out, 1 bit)
- Input 15: Input 15: K1 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7476: dual J-K Flipflops with preset and clear | 5.0.0 | new in 5.0.0 | TTL 7400-series library |
|---|
7485: 4-bit magnitude comparatorJava class Ttl7485, saved in files as library TTL. - Input 1: Input 1: B3 (in, 1 bit)
- Input 2: Input 2: A<B (in, 1 bit)
- Input 3: Input 3: A=B (in, 1 bit)
- Input 4: Input 4: A>B (in, 1 bit)
- Output 5: Output 5: A>B (out, 1 bit)
- Output 6: Output 6: A=B (out, 1 bit)
- Output 7: Output 7: A<B (out, 1 bit)
- Input 9: Input 9: B0 (in, 1 bit)
- Input 10: Input 10: A0 (in, 1 bit)
- Input 11: Input 11: B1 (in, 1 bit)
- Input 12: Input 12: A1 (in, 1 bit)
- Input 13: Input 13: A2 (in, 1 bit)
- Input 14: Input 14: B2 (in, 1 bit)
- Input 15: Input 15: A3 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7485: 4-bit magnitude comparator | 2.15.0 | no | TTL 7400-series library |
|---|
7486: quad 2-input XOR gateJava class Ttl7486, saved in files as library TTL. - Input: Input : 1 (in, 1 bit)
- Input: Input : 2 (in, 1 bit)
- Output: Output : 3 (out, 1 bit)
- Input: Input : 4 (in, 1 bit)
- Input: Input : 5 (in, 1 bit)
- Output: Output : 6 (out, 1 bit)
- Output: Output : 8 (out, 1 bit)
- Input: Input : 9 (in, 1 bit)
- Input: Input : 10 (in, 1 bit)
- Output: Output : 11 (out, 1 bit)
- Input: Input : 12 (in, 1 bit)
- Input: Input : 13 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7486: quad 2-input XOR gate | 2.15.0 | no | TTL 7400-series library |
|---|
7487: 4-bit True/complement, zero/one elementsJava class Ttl7487, saved in files as library TTL. - Input 1: Input 1: C (in, 1 bit)
- Input 2: Input 2: A1 (in, 1 bit)
- Output 3: Output 3: Y1 (out, 1 bit)
- Input 5: Input 5: A2 (in, 1 bit)
- Output 6: Output 6: Y2 (out, 1 bit)
- Input 8: Input 8: B (in, 1 bit)
- Output 9: Output 9: Y3 (out, 1 bit)
- Input 10: Input 10: A3 (in, 1 bit)
- Output 12: Output 12: Y4 (out, 1 bit)
- Input 13: Input 13: A4 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7487: 4-bit True/complement, zero/one elements | 3.9.0 | no | TTL 7400-series library |
|---|
7493: 4-bit binary ripple counterJava class Ttl7493, saved in files as library TTL. - Input 1: Input 1: CKB (Clock B) (in, 1 bit)
- Input 2: Input 2: R0(1) (Reset, active HIGH) (in, 1 bit)
- Input 3: Input 3: R0(2) (Reset, active HIGH) (in, 1 bit)
- Output 8: Output 8: QC (out, 1 bit)
- Output 9: Output 9: QB (out, 1 bit)
- Output 11: Output 11: QD (out, 1 bit)
- Output 12: Output 12: QA (out, 1 bit)
- Input 14: Input 14: CKA (Clock A) (in, 1 bit)
| TTL | Model of the 74-series TTL chip 7493: 4-bit binary ripple counter | 5.0.0 | new in 5.0.0 | TTL 7400-series library |
|---|
74125: quad bus buffer, three-state outputs, negative enableJava class Ttl74125, saved in files as library TTL. - Input: Input : 1 (in, 1 bit)
- Input: Input : 2 (in, 1 bit)
- Output: Output : 3 (out, 1 bit)
- Input: Input : 4 (in, 1 bit)
- Input: Input : 5 (in, 1 bit)
- Output: Output : 6 (out, 1 bit)
- Output: Output : 8 (out, 1 bit)
- Input: Input : 9 (in, 1 bit)
- Input: Input : 10 (in, 1 bit)
- Output: Output : 11 (out, 1 bit)
- Input: Input : 12 (in, 1 bit)
- Input: Input : 13 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74125: quad bus buffer, three-state outputs, negative enable | 2.15.0 | no | TTL 7400-series library |
|---|
74138: 3-line to 8-line decoderJava class Ttl74138, saved in files as library TTL. - Input 1: Input 1: A (in, 1 bit)
- Input 2: Input 2: B (in, 1 bit)
- Input 3: Input 3: C (in, 1 bit)
- Input 4: Input 4: nG2A Enable (active LOW) (in, 1 bit)
- Input 5: Input 5: nG2B Enable (active LOW) (in, 1 bit)
- Input 6: Input 6: G1 Enable (active HIGH) (in, 1 bit)
- Output 7: Output 7: nY7 (out, 1 bit)
- Output 9: Output 9: nY6 (out, 1 bit)
- Output 10: Output 10: nY5 (out, 1 bit)
- Output 11: Output 11: nY4 (out, 1 bit)
- Output 12: Output 12: nY3 (out, 1 bit)
- Output 13: Output 13: nY2 (out, 1 bit)
- Output 14: Output 14: nY1 (out, 1 bit)
- Output 15: Output 15: nY0 (out, 1 bit)
| TTL | Model of the 74-series TTL chip 74138: 3-line to 8-line decoder | 3.8.0 | no | TTL 7400-series library |
|---|
74139: Dual 2-line to 4-line decoderJava class Ttl74139, saved in files as library TTL. - Input 1: Input 1: 1nG Enable (active LOW) (in, 1 bit)
- Input 2: Input 2: 1A (in, 1 bit)
- Input 3: Input 3: 1B (in, 1 bit)
- Output 4: Output 4: 1nY0 (out, 1 bit)
- Output 5: Output 5: 1nY1 (out, 1 bit)
- Output 6: Output 6: 1nY2 (out, 1 bit)
- Output 7: Output 7: 1nY3 (out, 1 bit)
- Output 9: Output 9: 2nY3 (out, 1 bit)
- Output 10: Output 10: 2nY2 (out, 1 bit)
- Output 11: Output 11: 2nY1 (out, 1 bit)
- Output 12: Output 12: 2nY0 (out, 1 bit)
- Input 13: Input 13: 2B (in, 1 bit)
- Input 14: Input 14: 2A (in, 1 bit)
- Input 15: Input 15: 2nG Enable (active LOW) (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74139: Dual 2-line to 4-line decoder | 3.6.0 | no | TTL 7400-series library |
|---|
74151: 8-line to 1 line data selectorJava class Ttl74151, saved in files as library TTL. - Input 1: Input 1: D3 (in, 1 bit)
- Input 2: Input 2: D2 (in, 1 bit)
- Input 3: Input 3: D1 (in, 1 bit)
- Input 4: Input 4: D0 (in, 1 bit)
- Output 5: Output 5: Y (out, 1 bit)
- Output 6: Output 6: W (out, 1 bit)
- Input 7: Input 7: nG (in, 1 bit)
- Input 9: Input 9: C (in, 1 bit)
- Input 10: Input 10: B (in, 1 bit)
- Input 11: Input 11: A (in, 1 bit)
- Input 12: Input 12: D7 (in, 1 bit)
- Input 13: Input 13: D6 (in, 1 bit)
- Input 14: Input 14: D5 (in, 1 bit)
- Input 15: Input 15: D4 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74151: 8-line to 1 line data selector | 3.9.0 | no | TTL 7400-series library |
|---|
74153: dual 4-line to 1 line data selectorJava class Ttl74153, saved in files as library TTL. - Input 1: Input 1: n1E (in, 1 bit)
- Input 2: Input 2: S1 (in, 1 bit)
- Input 3: Input 3: 1D3 (in, 1 bit)
- Input 4: Input 4: 1D2 (in, 1 bit)
- Input 5: Input 5: 1D1 (in, 1 bit)
- Input 6: Input 6: 1D0 (in, 1 bit)
- Output 7: Output 7: 1Y (out, 1 bit)
- Output 9: Output 9: 2Y (out, 1 bit)
- Input 10: Input 10: 2D0 (in, 1 bit)
- Input 11: Input 11: 2D1 (in, 1 bit)
- Input 12: Input 12: 2D2 (in, 1 bit)
- Input 13: Input 13: 2D3 (in, 1 bit)
- Input 14: Input 14: S0 (in, 1 bit)
- Input 15: Input 15: n2E (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74153: dual 4-line to 1 line data selector | 3.9.0 | no | TTL 7400-series library |
|---|
74157: quad 2-line to 1 line data selectorJava class Ttl74157, saved in files as library TTL. - Input 1: Input 1: SELECT (in, 1 bit)
- Input 2: Input 2: 1A (in, 1 bit)
- Input 3: Input 3: 1B (in, 1 bit)
- Output 4: Output 4: 1Y (out, 1 bit)
- Input 5: Input 5: 2A (in, 1 bit)
- Input 6: Input 6: 2B (in, 1 bit)
- Output 7: Output 7: 2Y (out, 1 bit)
- Output 9: Output 9: 3Y (out, 1 bit)
- Input 10: Input 10: 3B (in, 1 bit)
- Input 11: Input 11: 3A (in, 1 bit)
- Output 12: Output 12: 4Y (out, 1 bit)
- Input 13: Input 13: 4B (in, 1 bit)
- Input 14: Input 14: 4A (in, 1 bit)
- Input 15: Input 15: nSTROBE (active LOW) (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74157: quad 2-line to 1 line data selector | 3.8.0 | no | TTL 7400-series library |
|---|
74158: quad 2-line to 1 line data selector, inverted outputJava class Ttl74158, saved in files as library TTL. - Input 1: Input 1: SELECT (in, 1 bit)
- Input 2: Input 2: 1A (in, 1 bit)
- Input 3: Input 3: 1B (in, 1 bit)
- Output 4: Output 4: 1Y (out, 1 bit)
- Input 5: Input 5: 2A (in, 1 bit)
- Input 6: Input 6: 2B (in, 1 bit)
- Output 7: Output 7: 2Y (out, 1 bit)
- Output 9: Output 9: 3Y (out, 1 bit)
- Input 10: Input 10: 3B (in, 1 bit)
- Input 11: Input 11: 3A (in, 1 bit)
- Output 12: Output 12: 4Y (out, 1 bit)
- Input 13: Input 13: 4B (in, 1 bit)
- Input 14: Input 14: 4A (in, 1 bit)
- Input 15: Input 15: nSTROBE (active LOW) (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74158: quad 2-line to 1 line data selector, inverted output | 3.8.0 | no | TTL 7400-series library |
|---|
74161: 4-bit sync counter with async clearJava class Ttl74161, saved in files as library TTL. - Input 1: Input 1: MR/CLR (Reset, active LOW) (in, 1 bit)
- Input 2: Input 2: CP/CLK (Clock) (in, 1 bit)
- Input 3: Input 3: D0/A (in, 1 bit)
- Input 4: Input 4: D1/B (in, 1 bit)
- Input 5: Input 5: D2/C (in, 1 bit)
- Input 6: Input 6: D3/D (in, 1 bit)
- Input 7: Input 7: CE/ENP (Count Enable) (in, 1 bit)
- Input 9: Input 9: PE/LOAD (Parallel Enable, active LOW) (in, 1 bit)
- Input 10: Input 10: CET/ENT (Count Enable Carry) (in, 1 bit)
- Output 11: Output 11: Q3/QD (out, 1 bit)
- Output 12: Output 12: Q2/QC (out, 1 bit)
- Output 13: Output 13: A1/QB (out, 1 bit)
- Output 14: Output 14: A0/QA (out, 1 bit)
- Output 15: Output 15: TC/RC0 (Terminal Count) (out, 1 bit)
| TTL | Model of the 74-series TTL chip 74161: 4-bit sync counter with async clear | 3.5.0 | no | TTL 7400-series library |
|---|
74163: 4-bit sync counter with sync clearJava class Ttl74163, saved in files as library TTL. - Input 1: Input 1: MR/CLR (Reset, active LOW) (in, 1 bit)
- Input 2: Input 2: CP/CLK (Clock) (in, 1 bit)
- Input 3: Input 3: D0/A (in, 1 bit)
- Input 4: Input 4: D1/B (in, 1 bit)
- Input 5: Input 5: D2/C (in, 1 bit)
- Input 6: Input 6: D3/D (in, 1 bit)
- Input 7: Input 7: CE/ENP (Count Enable) (in, 1 bit)
- Input 9: Input 9: PE/LOAD (Parallel Enable, active LOW) (in, 1 bit)
- Input 10: Input 10: CET/ENT (Count Enable Carry) (in, 1 bit)
- Output 11: Output 11: Q3/QD (out, 1 bit)
- Output 12: Output 12: Q2/QC (out, 1 bit)
- Output 13: Output 13: A1/QB (out, 1 bit)
- Output 14: Output 14: A0/QA (out, 1 bit)
- Output 15: Output 15: TC/RC0 (Terminal Count) (out, 1 bit)
| TTL | Model of the 74-series TTL chip 74163: 4-bit sync counter with sync clear | 3.6.0 | no | TTL 7400-series library |
|---|
74164: 8-bit serial-to-parallel shift registerJava class Ttl74164, saved in files as library TTL. - Input 1: Input 1: A (in, 1 bit)
- Input 2: Input 2: B (in, 1 bit)
- Output 3: Output 3: QA (out, 1 bit)
- Output 4: Output 4: QB (out, 1 bit)
- Output 5: Output 5: QC (out, 1 bit)
- Output 6: Output 6: QD (out, 1 bit)
- Input 8: Input 8: Clock (in, 1 bit)
- Input 9: Input 9: Clear (in, 1 bit)
- Output 10: Output 10: QE (out, 1 bit)
- Output 11: Output 11: QF (out, 1 bit)
- Output 12: Output 12: QG (out, 1 bit)
- Output 13: Output 13: QH (out, 1 bit)
| TTL | Model of the 74-series TTL chip 74164: 8-bit serial-to-parallel shift register | 3.8.0 | no | TTL 7400-series library |
|---|
74165: 8-bit parallel-to-serial shift registerJava class Ttl74165, saved in files as library TTL. - Input 1: Input 1: Shift/Load (in, 1 bit)
- Input 2: Input 2: Clock (in, 1 bit)
- Input 3: Input 3: P4 (in, 1 bit)
- Input 4: Input 4: P5 (in, 1 bit)
- Input 5: Input 5: P6 (in, 1 bit)
- Input 6: Input 6: P7 (in, 1 bit)
- Output 7: Output 7: Q7n (out, 1 bit)
- Output 9: Output 9: Q7 (out, 1 bit)
- Input 10: Input 10: Serial Input (in, 1 bit)
- Input 11: Input 11: P0 (in, 1 bit)
- Input 12: Input 12: P1 (in, 1 bit)
- Input 13: Input 13: P2 (in, 1 bit)
- Input 14: Input 14: P3 (in, 1 bit)
- Input 15: Input 15: Clock Inhibit (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74165: 8-bit parallel-to-serial shift register | 2.15.0 | no | TTL 7400-series library |
|---|
74166: 8-bit parallel-to-serial shift register with asynchronous clearJava class Ttl74166, saved in files as library TTL. - Input 1: Input 1: Serial Input (in, 1 bit)
- Input 2: Input 2: P0 (in, 1 bit)
- Input 3: Input 3: P1 (in, 1 bit)
- Input 4: Input 4: P2 (in, 1 bit)
- Input 5: Input 5: P3 (in, 1 bit)
- Input 6: Input 6: Clock Inhibit (in, 1 bit)
- Input 7: Input 7: Clock (in, 1 bit)
- Input 9: Input 9: Clear (in, 1 bit)
- Input 10: Input 10: P4 (in, 1 bit)
- Input 11: Input 11: P5 (in, 1 bit)
- Input 12: Input 12: P6 (in, 1 bit)
- Output 13: Output 13: Q7 (out, 1 bit)
- Input 14: Input 14: P7 (in, 1 bit)
- Input 15: Input 15: Shift/Load (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74166: 8-bit parallel-to-serial shift register with asynchronous clear | 3.8.0 | no | TTL 7400-series library |
|---|
74173: 4-bit D-type registers with 3-state outputsJava class Ttl74173, saved in files as library TTL. - Input 1: Input 1: nM (in, 1 bit)
- Input 2: Input 2: nN (in, 1 bit)
- Output 3: Output 3: Q1 (out, 1 bit)
- Output 4: Output 4: Q2 (out, 1 bit)
- Output 5: Output 5: Q3 (out, 1 bit)
- Output 6: Output 6: Q4 (out, 1 bit)
- Input 7: Input 7: CLK (in, 1 bit)
- Input 9: Input 9: nG1 (in, 1 bit)
- Input 10: Input 10: nG2 (in, 1 bit)
- Input 11: Input 11: D4 (in, 1 bit)
- Input 12: Input 12: D3 (in, 1 bit)
- Input 13: Input 13: D2 (in, 1 bit)
- Input 14: Input 14: D1 (in, 1 bit)
- Input 15: Input 15: CLR (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74173: 4-bit D-type registers with 3-state outputs | 5.0.0 | new in 5.0.0 | TTL 7400-series library |
|---|
74175: quad D-flipflop, asynchronous resetJava class Ttl74175, saved in files as library TTL. - Input 1: Input 1: nCLR (in, 1 bit)
- Output 2: Output 2: Q1 (out, 1 bit)
- Output 3: Output 3: nQ1 (out, 1 bit)
- Input 4: Input 4: D1 (in, 1 bit)
- Input 5: Input 5: D2 (in, 1 bit)
- Output 6: Output 6: nQ2 (out, 1 bit)
- Output 7: Output 7: Q2 (out, 1 bit)
- Input 9: Input 9: CLK (in, 1 bit)
- Output 10: Output 10: Q3 (out, 1 bit)
- Output 11: Output 11: nQ3 (out, 1 bit)
- Input 12: Input 12: D3 (in, 1 bit)
- Input 13: Input 13: D4 (in, 1 bit)
- Output 14: Output 14: nQ4 (out, 1 bit)
- Output 15: Output 15: Q4 (out, 1 bit)
| TTL | Model of the 74-series TTL chip 74175: quad D-flipflop, asynchronous reset | 2.15.0 | no | TTL 7400-series library |
|---|
74181: arithmetic logic unitJava class Ttl74181, saved in files as library TTL. - Input 1: Input 1: B0 (in, 1 bit)
- Input 2: Input 2: A0 (in, 1 bit)
- Input 3: Input 3: S3 (in, 1 bit)
- Input 4: Input 4: S2 (in, 1 bit)
- Input 5: Input 5: S1 (in, 1 bit)
- Input 6: Input 6: S0 (in, 1 bit)
- Input 7: Input 7: nCi (in, 1 bit)
- Input 8: Input 8: M (in, 1 bit)
- Output 9: Output 9: F0 (out, 1 bit)
- Output 10: Output 10: F1 (out, 1 bit)
- Output 11: Output 11: F2 (out, 1 bit)
- Output 13: Output 13: F3 (out, 1 bit)
- Output 14: Output 14: A=B (out, 1 bit)
- Output 15: Output 15: Pn (out, 1 bit)
- Output 16: Output 16: Co (out, 1 bit)
- Output 17: Output 17: Gn (out, 1 bit)
- Input 18: Input 18: B3 (in, 1 bit)
- Input 19: Input 19: A3 (in, 1 bit)
- Input 20: Input 20: B2 (in, 1 bit)
- Input 21: Input 21: A2 (in, 1 bit)
- Input 22: Input 22: B1 (in, 1 bit)
- Input 23: Input 23: A1 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74181: arithmetic logic unit | 3.9.0 | no | TTL 7400-series library |
|---|
74182: look-ahead carry generatorJava class Ttl74182, saved in files as library TTL. - Input 1: Input 1: G1 (in, 1 bit)
- Input 2: Input 2: P1 (in, 1 bit)
- Input 3: Input 3: G0 (in, 1 bit)
- Input 4: Input 4: P0 (in, 1 bit)
- Input 5: Input 5: G3 (in, 1 bit)
- Input 6: Input 6: P3 (in, 1 bit)
- Output 7: Output 7: P (out, 1 bit)
- Output 9: Output 9: Cnz (out, 1 bit)
- Output 10: Output 10: G (out, 1 bit)
- Output 11: Output 11: Cny (out, 1 bit)
- Output 12: Output 12: Cnx (out, 1 bit)
- Input 13: Input 13: Cn (in, 1 bit)
- Input 14: Input 14: G2 (in, 1 bit)
- Input 15: Input 15: P2 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74182: look-ahead carry generator | 3.9.0 | no | TTL 7400-series library |
|---|
74192: 4-bit up/down decade counterJava class Ttl74192, saved in files as library TTL. - Input 1: Input 1: Data Input B (in, 1 bit)
- Output 2: Output 2: Data Output B (out, 1 bit)
- Output 3: Output 3: Data Output A (out, 1 bit)
- Input 4: Input 4: Count Down (in, 1 bit)
- Input 5: Input 5: Count Up (in, 1 bit)
- Output 6: Output 6: Data Output C (out, 1 bit)
- Output 7: Output 7: Data Output D (out, 1 bit)
- Input 9: Input 9: Data Input D (in, 1 bit)
- Input 10: Input 10: Data Input C (in, 1 bit)
- Input 11: Input 11: Load (in, 1 bit)
- Output 12: Output 12: Carry (out, 1 bit)
- Output 13: Output 13: Borrow (out, 1 bit)
- Input 14: Input 14: Clear (in, 1 bit)
- Input 15: Input 15: Data Input A (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74192: 4-bit up/down decade counter | 3.8.0 | no | TTL 7400-series library |
|---|
74193: 4-bit up/down binary counterJava class Ttl74193, saved in files as library TTL. - Input 1: Input 1: Data Input B (in, 1 bit)
- Output 2: Output 2: Data Output B (out, 1 bit)
- Output 3: Output 3: Data Output A (out, 1 bit)
- Input 4: Input 4: Count Down (in, 1 bit)
- Input 5: Input 5: Count Up (in, 1 bit)
- Output 6: Output 6: Data Output C (out, 1 bit)
- Output 7: Output 7: Data Output D (out, 1 bit)
- Input 9: Input 9: Data Input D (in, 1 bit)
- Input 10: Input 10: Data Input C (in, 1 bit)
- Input 11: Input 11: Load (in, 1 bit)
- Output 12: Output 12: Carry (out, 1 bit)
- Output 13: Output 13: Borrow (out, 1 bit)
- Input 14: Input 14: Clear (in, 1 bit)
- Input 15: Input 15: Data Input A (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74193: 4-bit up/down binary counter | 3.8.0 | no | TTL 7400-series library |
|---|
74194: 4-bit bidirectional universal shift registerJava class Ttl74194, saved in files as library TTL. - Input 1: Input 1: nCLR (in, 1 bit)
- Input 2: Input 2: SR (in, 1 bit)
- Input 3: Input 3: A (in, 1 bit)
- Input 4: Input 4: B (in, 1 bit)
- Input 5: Input 5: C (in, 1 bit)
- Input 6: Input 6: D (in, 1 bit)
- Input 7: Input 7: SL (in, 1 bit)
- Input 9: Input 9: S0 (in, 1 bit)
- Input 10: Input 10: S1 (in, 1 bit)
- Input 11: Input 11: CLK (in, 1 bit)
- Output 12: Output 12: QD (out, 1 bit)
- Output 13: Output 13: QC (out, 1 bit)
- Output 14: Output 14: QB (out, 1 bit)
- Output 15: Output 15: QA (out, 1 bit)
| TTL | Model of the 74-series TTL chip 74194: 4-bit bidirectional universal shift register | 4.0.0 | no | TTL 7400-series library |
|---|
74240: octal buffers with three-state inverted outputsJava class Ttl74240, saved in files as library TTL. - Input 1: Input 1: n1G (in, 1 bit)
- Input 2: Input 2: 1A1 (in, 1 bit)
- Output 3: Output 3: n2Y4 (out, 1 bit)
- Input 4: Input 4: 1A2 (in, 1 bit)
- Output 5: Output 5: n2Y3 (out, 1 bit)
- Input 6: Input 6: 1A3 (in, 1 bit)
- Output 7: Output 7: n2Y2 (out, 1 bit)
- Input 8: Input 8: 1A4 (in, 1 bit)
- Output 9: Output 9: n2Y1 (out, 1 bit)
- Input 11: Input 11: 2A1 (in, 1 bit)
- Output 12: Output 12: n1Y4 (out, 1 bit)
- Input 13: Input 13: 2A2 (in, 1 bit)
- Output 14: Output 14: n1Y3 (out, 1 bit)
- Input 15: Input 15: 2A3 (in, 1 bit)
- Output 16: Output 16: n1Y2 (out, 1 bit)
- Input 17: Input 17: 2A4 (in, 1 bit)
- Output 18: Output 18: n1Y1 (out, 1 bit)
- Input 19: Input 19: n2G (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74240: octal buffers with three-state inverted outputs | 3.8.0 | no | TTL 7400-series library |
|---|
74241: octal buffers with three-state outputs and complementary enablesJava class Ttl74241, saved in files as library TTL. - Input 1: Input 1: n1G (in, 1 bit)
- Input 2: Input 2: 1A1 (in, 1 bit)
- Output 3: Output 3: 2Y4 (out, 1 bit)
- Input 4: Input 4: 1A2 (in, 1 bit)
- Output 5: Output 5: 2Y3 (out, 1 bit)
- Input 6: Input 6: 1A3 (in, 1 bit)
- Output 7: Output 7: 2Y2 (out, 1 bit)
- Input 8: Input 8: 1A4 (in, 1 bit)
- Output 9: Output 9: 2Y1 (out, 1 bit)
- Input 11: Input 11: 2A1 (in, 1 bit)
- Output 12: Output 12: 1Y4 (out, 1 bit)
- Input 13: Input 13: 2A2 (in, 1 bit)
- Output 14: Output 14: 1Y3 (out, 1 bit)
- Input 15: Input 15: 2A3 (in, 1 bit)
- Output 16: Output 16: 1Y2 (out, 1 bit)
- Input 17: Input 17: 2A4 (in, 1 bit)
- Output 18: Output 18: 1Y1 (out, 1 bit)
- Input 19: Input 19: 2G (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74241: octal buffers with three-state outputs and complementary enables | 3.8.0 | no | TTL 7400-series library |
|---|
74244: octal buffers with three-state outputsJava class Ttl74244, saved in files as library TTL. - Input 1: Input 1: n1G (in, 1 bit)
- Input 2: Input 2: 1A1 (in, 1 bit)
- Output 3: Output 3: 2Y4 (out, 1 bit)
- Input 4: Input 4: 1A2 (in, 1 bit)
- Output 5: Output 5: 2Y3 (out, 1 bit)
- Input 6: Input 6: 1A3 (in, 1 bit)
- Output 7: Output 7: 2Y2 (out, 1 bit)
- Input 8: Input 8: 1A4 (in, 1 bit)
- Output 9: Output 9: 2Y1 (out, 1 bit)
- Input 11: Input 11: 2A1 (in, 1 bit)
- Output 12: Output 12: 1Y4 (out, 1 bit)
- Input 13: Input 13: 2A2 (in, 1 bit)
- Output 14: Output 14: 1Y3 (out, 1 bit)
- Input 15: Input 15: 2A3 (in, 1 bit)
- Output 16: Output 16: 1Y2 (out, 1 bit)
- Input 17: Input 17: 2A4 (in, 1 bit)
- Output 18: Output 18: 1Y1 (out, 1 bit)
- Input 19: Input 19: n2G (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74244: octal buffers with three-state outputs | 3.8.0 | no | TTL 7400-series library |
|---|
74245: octal bus transceivers with three-state outputsJava class Ttl74245, saved in files as library TTL. - Input 1: Input 1: DIR (in, 1 bit)
- Input/Output 2: Input/Output 2: A1 (inout, 1 bit)
- Input/Output 3: Input/Output 3: A2 (inout, 1 bit)
- Input/Output 4: Input/Output 4: A3 (inout, 1 bit)
- Input/Output 5: Input/Output 5: A4 (inout, 1 bit)
- Input/Output 6: Input/Output 6: A5 (inout, 1 bit)
- Input/Output 7: Input/Output 7: A6 (inout, 1 bit)
- Input/Output 8: Input/Output 8: A7 (inout, 1 bit)
- Input/Output 9: Input/Output 9: A8 (inout, 1 bit)
- Input/Output 11: Input/Output 11: B8 (inout, 1 bit)
- Input/Output 12: Input/Output 12: B7 (inout, 1 bit)
- Input/Output 13: Input/Output 13: B6 (inout, 1 bit)
- Input/Output 14: Input/Output 14: B5 (inout, 1 bit)
- Input/Output 15: Input/Output 15: B4 (inout, 1 bit)
- Input/Output 16: Input/Output 16: B3 (inout, 1 bit)
- Input/Output 17: Input/Output 17: B2 (inout, 1 bit)
- Input/Output 18: Input/Output 18: B1 (inout, 1 bit)
- Input 19: Input 19: nOE (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74245: octal bus transceivers with three-state outputs | 3.8.0 | no | TTL 7400-series library |
|---|
74266: quad 2-input XNOR gate (open-collector)Java class Ttl74266, saved in files as library TTL. - Input: Input : 1 (in, 1 bit)
- Input: Input : 2 (in, 1 bit)
- Output: Output : 3 (out, 1 bit)
- Input: Input : 4 (in, 1 bit)
- Input: Input : 5 (in, 1 bit)
- Output: Output : 6 (out, 1 bit)
- Output: Output : 8 (out, 1 bit)
- Input: Input : 9 (in, 1 bit)
- Input: Input : 10 (in, 1 bit)
- Output: Output : 11 (out, 1 bit)
- Input: Input : 12 (in, 1 bit)
- Input: Input : 13 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74266: quad 2-input XNOR gate (open-collector) | 3.8.0 | no | TTL 7400-series library |
|---|
74273: octal D-Flipflop with clearJava class Ttl74273, saved in files as library TTL. - Input 1: Input 1: nCLR (in, 1 bit)
- Output 2: Output 2: Q1 (out, 1 bit)
- Input 3: Input 3: D1 (in, 1 bit)
- Input 4: Input 4: D2 (in, 1 bit)
- Output 5: Output 5: Q2 (out, 1 bit)
- Output 6: Output 6: Q3 (out, 1 bit)
- Input 7: Input 7: D3 (in, 1 bit)
- Input 8: Input 8: D4 (in, 1 bit)
- Output 9: Output 9: Q4 (out, 1 bit)
- Input 11: Input 11: CLK (in, 1 bit)
- Output 12: Output 12: Q5 (out, 1 bit)
- Input 13: Input 13: D5 (in, 1 bit)
- Input 14: Input 14: D6 (in, 1 bit)
- Output 15: Output 15: Q6 (out, 1 bit)
- Output 16: Output 16: Q7 (out, 1 bit)
- Input 17: Input 17: D7 (in, 1 bit)
- Input 18: Input 18: D8 (in, 1 bit)
- Output 19: Output 19: Q8 (out, 1 bit)
| TTL | Model of the 74-series TTL chip 74273: octal D-Flipflop with clear | 2.15.0 | no | TTL 7400-series library |
|---|
74283: 4-bit binary full adderJava class Ttl74283, saved in files as library TTL. - Output 1: Output 1: ∑2 (out, 1 bit)
- Input 2: Input 2: B2 (in, 1 bit)
- Input 3: Input 3: A2 (in, 1 bit)
- Output 4: Output 4: ∑1 (out, 1 bit)
- Input 5: Input 5: A1 (in, 1 bit)
- Input 6: Input 6: B1 (in, 1 bit)
- Input 7: Input 7: CIN (in, 1 bit)
- Output 9: Output 9: C4 (out, 1 bit)
- Output 10: Output 10: ∑4 (out, 1 bit)
- Input 11: Input 11: B4 (in, 1 bit)
- Input 12: Input 12: A4 (in, 1 bit)
- Output 13: Output 13: ∑3 (out, 1 bit)
- Input 14: Input 14: A3 (in, 1 bit)
- Input 15: Input 15: B3 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74283: 4-bit binary full adder | 2.15.0 | no | TTL 7400-series library |
|---|
74299: 8-bit universal shift register with three-state outputsJava class Ttl74299, saved in files as library TTL. - Input 1: Input 1: S0 (in, 1 bit)
- Input 2: Input 2: nOE1 (in, 1 bit)
- Input 3: Input 3: nOE2 (in, 1 bit)
- Output 4: Output 4: IOG (out, 1 bit)
- Output 5: Output 5: IOE (out, 1 bit)
- Output 6: Output 6: IOC (out, 1 bit)
- Output 7: Output 7: IOA (out, 1 bit)
- Output 8: Output 8: QA (out, 1 bit)
- Input 9: Input 9: nCLR (in, 1 bit)
- Input 11: Input 11: SR (in, 1 bit)
- Input 12: Input 12: CLK (in, 1 bit)
- Output 13: Output 13: IOB (out, 1 bit)
- Output 14: Output 14: IOD (out, 1 bit)
- Output 15: Output 15: IOF (out, 1 bit)
- Output 16: Output 16: IOH (out, 1 bit)
- Output 17: Output 17: QH (out, 1 bit)
- Input 18: Input 18: SL (in, 1 bit)
- Input 19: Input 19: S1 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74299: 8-bit universal shift register with three-state outputs | 3.9.0 | no | TTL 7400-series library |
|---|
74377: octal D-Flipflop with enableJava class Ttl74377, saved in files as library TTL. - Input 1: Input 1: nCLKen (in, 1 bit)
- Output 2: Output 2: Q1 (out, 1 bit)
- Input 3: Input 3: D1 (in, 1 bit)
- Input 4: Input 4: D2 (in, 1 bit)
- Output 5: Output 5: Q2 (out, 1 bit)
- Output 6: Output 6: Q3 (out, 1 bit)
- Input 7: Input 7: D3 (in, 1 bit)
- Input 8: Input 8: D4 (in, 1 bit)
- Output 9: Output 9: Q4 (out, 1 bit)
- Input 11: Input 11: CLK (in, 1 bit)
- Output 12: Output 12: Q5 (out, 1 bit)
- Input 13: Input 13: D5 (in, 1 bit)
- Input 14: Input 14: D6 (in, 1 bit)
- Output 15: Output 15: Q6 (out, 1 bit)
- Output 16: Output 16: Q7 (out, 1 bit)
- Input 17: Input 17: D7 (in, 1 bit)
- Input 18: Input 18: D8 (in, 1 bit)
- Output 19: Output 19: Q8 (out, 1 bit)
| TTL | Model of the 74-series TTL chip 74377: octal D-Flipflop with enable | 2.15.0 | no | TTL 7400-series library |
|---|
74381: arithmetic logic unit (ALU)Java class Ttl74381, saved in files as library TTL. - Input 1: Input 1: A1 (in, 1 bit)
- Input 2: Input 2: B1 (in, 1 bit)
- Input 3: Input 3: A0 (in, 1 bit)
- Input 4: Input 4: B0 (in, 1 bit)
- Input 5: Input 5: S0 (in, 1 bit)
- Input 6: Input 6: S1 (in, 1 bit)
- Input 7: Input 7: S2 (in, 1 bit)
- Output 8: Output 8: F0 (out, 1 bit)
- Output 9: Output 9: F1 (out, 1 bit)
- Output 11: Output 11: F2 (out, 1 bit)
- Output 12: Output 12: F3 (out, 1 bit)
- Output 13: Output 13: Gn (out, 1 bit)
- Output 14: Output 14: Pn (out, 1 bit)
- Input 15: Input 15: Ci (in, 1 bit)
- Input 16: Input 16: B3 (in, 1 bit)
- Input 17: Input 17: A3 (in, 1 bit)
- Input 18: Input 18: B2 (in, 1 bit)
- Input 19: Input 19: A2 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74381: arithmetic logic unit (ALU) | 3.9.0 | no | TTL 7400-series library |
|---|
74541: Octal buffers with three-state outputsJava class Ttl74541, saved in files as library TTL. - Input 1: Input 1: nOE1 (in, 1 bit)
- Input 2: Input 2: A1 (in, 1 bit)
- Input 3: Input 3: A2 (in, 1 bit)
- Input 4: Input 4: A3 (in, 1 bit)
- Input 5: Input 5: A4 (in, 1 bit)
- Input 6: Input 6: A5 (in, 1 bit)
- Input 7: Input 7: A6 (in, 1 bit)
- Input 8: Input 8: A7 (in, 1 bit)
- Input 9: Input 9: A8 (in, 1 bit)
- Output 11: Output 11: Y8 (out, 1 bit)
- Output 12: Output 12: Y7 (out, 1 bit)
- Output 13: Output 13: Y6 (out, 1 bit)
- Output 14: Output 14: Y5 (out, 1 bit)
- Output 15: Output 15: Y4 (out, 1 bit)
- Output 16: Output 16: Y3 (out, 1 bit)
- Output 17: Output 17: Y2 (out, 1 bit)
- Output 18: Output 18: Y1 (out, 1 bit)
- Input 19: Input 19: nOE2 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74541: Octal buffers with three-state outputs | 3.9.0 | no | TTL 7400-series library |
|---|
74670: 4-by-4 register file with three-state outputsJava class Ttl74670, saved in files as library TTL. - Input 1: Input 1: D2 (in, 1 bit)
- Input 2: Input 2: D3 (in, 1 bit)
- Input 3: Input 3: D4 (in, 1 bit)
- Input 4: Input 4: RA1 (in, 1 bit)
- Input 5: Input 5: RA0 (in, 1 bit)
- Output 6: Output 6: Q4 (out, 1 bit)
- Output 7: Output 7: Q3 (out, 1 bit)
- Output 9: Output 9: Q2 (out, 1 bit)
- Output 10: Output 10: Q1 (out, 1 bit)
- Input 11: Input 11: nOE (in, 1 bit)
- Input 12: Input 12: nWE (in, 1 bit)
- Input 13: Input 13: WA1 (in, 1 bit)
- Input 14: Input 14: WA0 (in, 1 bit)
- Input 15: Input 15: D1 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 74670: 4-by-4 register file with three-state outputs | 3.9.0 | no | TTL 7400-series library |
|---|
747266: quad 2-input XNOR gateJava class Ttl747266, saved in files as library TTL. - Input: Input : 1 (in, 1 bit)
- Input: Input : 2 (in, 1 bit)
- Output: Output : 3 (out, 1 bit)
- Input: Input : 4 (in, 1 bit)
- Input: Input : 5 (in, 1 bit)
- Output: Output : 6 (out, 1 bit)
- Output: Output : 8 (out, 1 bit)
- Input: Input : 9 (in, 1 bit)
- Input: Input : 10 (in, 1 bit)
- Output: Output : 11 (out, 1 bit)
- Input: Input : 12 (in, 1 bit)
- Input: Input : 13 (in, 1 bit)
| TTL | Model of the 74-series TTL chip 747266: quad 2-input XNOR gate | 2.15.0 | no | TTL 7400-series library |
|---|
NOT GateJava class NotGate, saved in files as library Gates. - out port (out, 1 bit)
- in port (in, 1 bit)
| Gates | Inverts its input. | before 2.13.9 | yes | Logic gates and buffers |
|---|
BufferJava class Buffer, saved in files as library Gates. - out port (out, 1 bit)
- in port (in, 1 bit)
| Gates | Passes its input through unchanged (useful for delay or drawing). | before 2.13.9 | yes | Logic gates and buffers |
|---|
AND GateJava class AndGate, saved in files as library Gates. - out port (out, 1 bit)
- in port (in, 1 bit)
- in port (in, 1 bit)
The default instance has 3 ports in 5.0.0 and 6 in 2.7.1. | Gates | Outputs 1 only when all inputs are 1. | before 2.13.9 | yes | Logic gates and buffers |
|---|
OR GateJava class OrGate, saved in files as library Gates. - out port (out, 1 bit)
- in port (in, 1 bit)
- in port (in, 1 bit)
The default instance has 3 ports in 5.0.0 and 6 in 2.7.1. | Gates | Outputs 1 when any input is 1. | before 2.13.9 | yes | Logic gates and buffers |
|---|
NAND GateJava class NandGate, saved in files as library Gates. - out port (out, 1 bit)
- in port (in, 1 bit)
- in port (in, 1 bit)
The default instance has 3 ports in 5.0.0 and 6 in 2.7.1. | Gates | Inverted AND. | before 2.13.9 | yes | Logic gates and buffers |
|---|
NOR GateJava class NorGate, saved in files as library Gates. - out port (out, 1 bit)
- in port (in, 1 bit)
- in port (in, 1 bit)
The default instance has 3 ports in 5.0.0 and 6 in 2.7.1. | Gates | Inverted OR. | before 2.13.9 | yes | Logic gates and buffers |
|---|
XOR GateJava class XorGate, saved in files as library Gates. - out port (out, 1 bit)
- in port (in, 1 bit)
- in port (in, 1 bit)
The default instance has 3 ports in 5.0.0 and 6 in 2.7.1. | Gates | Exclusive OR (one-hot or odd-parity behaviour selectable). | before 2.13.9 | yes | Logic gates and buffers |
|---|
XNOR GateJava class XnorGate, saved in files as library Gates. - out port (out, 1 bit)
- in port (in, 1 bit)
- in port (in, 1 bit)
The default instance has 3 ports in 5.0.0 and 6 in 2.7.1. | Gates | Inverted exclusive OR. | before 2.13.9 | yes | Logic gates and buffers |
|---|
Odd ParityJava class OddParityGate, saved in files as library Gates. - out port (out, 1 bit)
- in port (in, 1 bit)
- in port (in, 1 bit)
The default instance has 3 ports in 5.0.0 and 6 in 2.7.1. | Gates | Outputs 1 when an odd number of inputs are 1. | before 2.13.9 | yes | Logic gates and buffers |
|---|
Even ParityJava class EvenParityGate, saved in files as library Gates. - out port (out, 1 bit)
- in port (in, 1 bit)
- in port (in, 1 bit)
The default instance has 3 ports in 5.0.0 and 6 in 2.7.1. | Gates | Outputs 1 when an even number of inputs are 1. | before 2.13.9 | yes | Logic gates and buffers |
|---|
Controlled BufferJava class ControlledBuffer, saved in files as library Gates. - out port (out, 1 bit)
- in port (in, 1 bit)
- in port (in, 1 bit)
| Gates | Tri-state buffer: passes input only while its control line is 1, otherwise floats. | before 2.13.9 | yes | Logic gates and buffers |
|---|
Controlled InverterJava class ControlledBuffer, saved in files as library Gates. - out port (out, 1 bit)
- in port (in, 1 bit)
- in port (in, 1 bit)
| Gates | Tri-state inverter controlled by an enable line. | before 2.13.9 | yes | Logic gates and buffers |
|---|
PLAJava class Pla, saved in files as library Gates. - input (in, 2 bits)
- output (out, 2 bits)
| Gates | Programmable logic array with an editable AND/OR plane. | 3.3.0 | no | Logic gates and buffers |
|---|
Binary to BCDJava class BinToBcd, saved in files as library BFH-Praktika. - Binary input (in, 9 bits)
- 1 (out, 4 bits)
- 10 (out, 4 bits)
- 100 (out, 4 bits)
| BFH mega functions | Converts a binary number into binary-coded-decimal digits. | 2.13.14 | no | this row |
|---|
BCD to seven segmentJava class BcdToSevenSegmentDisplay, saved in files as library BFH-Praktika. - Segment A (out, 1 bit)
- Segment B (out, 1 bit)
- Segment C (out, 1 bit)
- Segment D (out, 1 bit)
- Segment E (out, 1 bit)
- Segment F (out, 1 bit)
- Segment G (out, 1 bit)
- BCD value (in, 4 bits)
| BFH mega functions | Decodes a BCD digit into 7-segment display drive lines. | 2.13.14 | no | this row |
|---|
MultiplexerJava class Multiplexer, saved in files as library Plexers. - Input 0 (in, 1 bit)
- Input 1 (in, 1 bit)
- Select: Select: identifies which input becomes output (in, 1 bit)
- Output (out, 1 bit)
The default instance has 4 ports in 5.0.0 and 5 in 2.7.1. | Plexers | Selects one of several inputs using a select value. | before 2.13.9 | yes | Multiplexers, decoders and encoders |
|---|
DemultiplexerJava class Demultiplexer, saved in files as library Plexers. - Output 0 (out, 1 bit)
- Output 1 (out, 1 bit)
- Select: Select: identifies which output receives input (in, 1 bit)
- Input (in, 1 bit)
The default instance has 4 ports in 5.0.0 and 5 in 2.7.1. | Plexers | Routes one input to one of several outputs. | before 2.13.9 | yes | Multiplexers, decoders and encoders |
|---|
DecoderJava class Decoder, saved in files as library Plexers. - Output 0 (out, 1 bit)
- Output 1 (out, 1 bit)
- Select: Select: identifies which output is 1 (in, 1 bit)
- Enable: Enable: when not 0, selected output is 1 (in, 1 bit)
| Plexers | Sets exactly one output high according to a select value. | before 2.13.9 | yes | Multiplexers, decoders and encoders |
|---|
Priority EncoderJava class PriorityEncoder, saved in files as library Plexers. - Input 0 (in, 1 bit)
- Input 1 (in, 1 bit)
- Input 2 (in, 1 bit)
- Input 3 (in, 1 bit)
- Input 4 (in, 1 bit)
- Input 5 (in, 1 bit)
- Input 6 (in, 1 bit)
- Input 7 (in, 1 bit)
- Output: Output: address of highest-indexed 1 input (out, 3 bits)
- Enable Input: Enable Input: 0 disables the component (in, 1 bit)
- Enable Output: Enable Output: 1 if enabled and no inputs are 1 (out, 1 bit)
- Group Select: Group Select: 1 if enabled and any input is 1 (out, 1 bit)
| Plexers | Outputs the index of the highest-priority active input. | before 2.13.9 | yes | Multiplexers, decoders and encoders |
|---|
Bit SelectorJava class BitSelector, saved in files as library Plexers. - Output: Output: value of selected group of bits from data (out, 1 bit)
- Data (in, 8 bits)
- Select: Select: identifies which group from data is selected (in, 3 bits)
| Plexers | Picks a group of bits out of a wider value. | before 2.13.9 | yes | Multiplexers, decoders and encoders |
|---|
ImageJava class Image, saved in files as library Base. | Base | Places a bitmap picture in a circuit or a subcircuit appearance (added 5.0.0). | 5.0.0 | new in 5.0.0 | this row |
|---|
ButtonJava class Button, saved in files as library I/O. | Input/Output | Momentary push-button input (1 while pressed). | before 2.13.9 | yes | this row |
|---|
Dip switchJava class DipSwitch, saved in files as library I/O. - DIP1 (out, 1 bit)
- DIP2 (out, 1 bit)
- DIP3 (out, 1 bit)
- DIP4 (out, 1 bit)
- DIP5 (out, 1 bit)
- DIP6 (out, 1 bit)
- DIP7 (out, 1 bit)
- DIP8 (out, 1 bit)
| Input/Output | Bank of on/off switches giving several input bits. | before 2.13.9 | no | this row |
|---|
JoystickJava class Joystick, saved in files as library I/O. - Output: Output: x-coordinate (out, 4 bits)
- Output: Output: y-coordinate (out, 4 bits)
| Input/Output | Two-axis joystick input producing X and Y values. | before 2.13.9 | yes | this row |
|---|
KeyboardJava class Keyboard, saved in files as library I/O. - Clear: Clear: 1 empties buffer (in, 1 bit)
- Clock: Clock: trigger consumes the buffer’s front character (in, 1 bit)
- Read enable: Read enable: 0 disables clock (in, 1 bit)
- Available: Available: 1 when buffer contains characters (out, 1 bit)
- Data: Data: ASCII value of buffer’s front character (out, 7 bits)
| Input/Output | Buffers characters typed by the user for the circuit to read. | before 2.13.9 | yes | Keyboard, TTY, LED matrix and video |
|---|
LEDJava class Led, saved in files as library I/O. | Input/Output | Lights when its input is 1. | before 2.13.9 | yes | this row |
|---|
LED BarJava class LedBar, saved in files as library I/O. - in port (in, 1 bit)
- in port (in, 1 bit)
- in port (in, 1 bit)
- in port (in, 1 bit)
- in port (in, 1 bit)
- in port (in, 1 bit)
- in port (in, 1 bit)
- in port (in, 1 bit)
| Input/Output | Row of LED segments driven by separate inputs or a bus. | 3.6.0 | no | this row |
|---|
RGB LEDJava class RgbLed, saved in files as library I/O. - Red input (in, 1 bit)
- Green input (in, 1 bit)
- Blue input (in, 1 bit)
| Input/Output | LED whose red, green and blue channels are driven separately. | before 2.13.9 | no | this row |
|---|
7-Segment DisplayJava class SevenSegment, saved in files as library I/O. - Segment A (in, 1 bit)
- Segment B (in, 1 bit)
- Segment C (in, 1 bit)
- Segment D (in, 1 bit)
- Segment E (in, 1 bit)
- Segment F (in, 1 bit)
- Segment G (in, 1 bit)
- Decimal point (in, 1 bit)
| Input/Output | Classic seven-segment digit plus decimal point, one input per segment. | before 2.13.9 | yes | 7-segment and hex digit displays |
|---|
Hex Digit DisplayJava class HexDigit, saved in files as library I/O. - Data: Data: nibble to display in hex (in, 4 bits)
- DecimalPoint: DecimalPoint: lights the decimal point (in, 1 bit)
| Input/Output | Shows a 4-bit value as a hexadecimal digit. | before 2.13.9 | yes | 7-segment and hex digit displays |
|---|
LED MatrixJava class DotMatrix, saved in files as library I/O. - in port (in, 7 bits)
- in port (in, 7 bits)
- in port (in, 7 bits)
- in port (in, 7 bits)
- in port (in, 7 bits)
| Input/Output | Grid of LEDs driven by rows, columns or select lines. | before 2.13.9 | yes | Keyboard, TTY, LED matrix and video |
|---|
TTYJava class Tty, saved in files as library I/O. - Clear: Clear: 1 clears screen (in, 1 bit)
- Clock: Clock: trigger adds character on input (in, 1 bit)
- Write enable: Write enable: 0 disables clock (in, 1 bit)
- Data: Data: ASCII value of next character to write (in, 7 bits)
| Input/Output | Text terminal that prints characters written by the circuit. | before 2.13.9 | yes | Keyboard, TTY, LED matrix and video |
|---|
Port I/OJava class PortIo, saved in files as library I/O. - Output enable (in, 1 bit)
- Outputs [0...7] (in, 8 bits)
- Inputs [0...7] (out, 8 bits)
| Input/Output | Group of GPIO-style pins that can act as inputs, outputs or both. | before 2.13.9 | no | this row |
|---|
Reptar Local BusJava class ReptarLocalBus, saved in files as library I/O. - B tip (out, 1 bit)
- B tip (out, 1 bit)
- B tip (out, 1 bit)
- B tip (out, 1 bit)
- B tip (in, 1 bit)
- B tip (out, 16 bits)
- B tip (in, 16 bits)
- B tip (in, 1 bit)
- B tip (out, 9 bits)
- B tip (in, 1 bit)
| Input/Output | Interface block for the REDS Reptar FPGA board's local bus; for FPGA export, not for simulation. | before 2.13.9 | no | this row |
|---|
TelnetJava class Telnet, saved in files as library I/O. - Input: Input: data to send (in, 8 bits)
- Output: Output: received data (out, 8 bits)
- Clock: Clock: send/receive data on clock edge (in, 1 bit)
- activate sending (in, 1 bit)
- activate receiving (in, 1 bit)
- Available: Available: data to read is available (out, 1 bit)
| Input/Output | Opens a TCP port so an external client can send and receive bytes to the circuit. | 4.0.0 | no | this row |
|---|
Real-Time ClockJava class RealTimeClock, saved in files as library I/O. - Milliseconds (out, 64 bits)
| Input/Output | Outputs current Unix-epoch time (ms or s) as a 64-bit value. | 5.0.0 | new in 5.0.0 | this row |
|---|
Matrix KeypadJava class MatrixKeypad, saved in files as library I/O. - Row 1 input (in, 1 bit)
- Row 2 input (in, 1 bit)
- Row 3 input (in, 1 bit)
- Row 4 input (in, 1 bit)
- Column 1 output (out, 1 bit)
- Column 2 output (out, 1 bit)
- Column 3 output (out, 1 bit)
- Column 4 output (out, 1 bit)
| Input/Output | 4x4 row/column keypad that a circuit scans like real hardware. | 5.0.0 | new in 5.0.0 | this row |
|---|
SwitchJava class Switch, saved in files as library Input/Output-Extra. - Input (in, 1 bit)
- Output (out, 1 bit)
| Input/Output Extra | Hand-operated on/off switch passing its input when closed. | 2.15.0 | no | this row |
|---|
BuzzerJava class Buzzer, saved in files as library Input/Output-Extra. - frequency (in, 14 bits)
- Enable sound (in, 1 bit)
- volume (in, 7 bits)
- Duty cycle (in, 8 bits)
| Input/Output Extra | Plays a tone on the computer's speaker when enabled. | 2.15.0 | no | this row |
|---|
SliderJava class Slider, saved in files as library Input/Output-Extra. | Input/Output Extra | Draggable control producing an unsigned value up to 8 bits. | 2.15.0 | no | this row |
|---|
Digital oscilloscopeJava class DigitalOscilloscope, saved in files as library Input/Output-Extra. - clock (in, 1 bit)
- in port (in, 1 bit)
- in port (in, 1 bit)
- in port (in, 1 bit)
- Enable Input: Enable Input: 0 disables the component (in, 1 bit)
- Clear diagram (in, 1 bit)
| Input/Output Extra | Records and plots 1-bit signals on each clock edge. | 2.15.0 | no | this row |
|---|
Two-Way SwitchJava class TwoWaySwitch, saved in files as library Input/Output-Extra. - Input (in, 1 bit)
- Output (out, 1 bit)
- Output (out, 1 bit)
| Input/Output Extra | Changeover switch selecting one of two paths. | 5.0.0 | new in 5.0.0 | this row |
|---|
2-Pin LEDJava class TwoPinLed, saved in files as library Input/Output-Extra. - Anode (in, 1 bit)
- Cathode (in, 1 bit)
| Input/Output Extra | LED with separate anode and cathode pins. | 5.0.0 | new in 5.0.0 | this row |
|---|
TCL REDS consoleJava class TclConsoleReds, saved in files as library TCL. - Hex0_obs (in, 4 bits)
- Hex1_obs (in, 4 bits)
- L0_obs (in, 1 bit)
- L1_obs (in, 1 bit)
- L2_obs (in, 1 bit)
- L3_obs (in, 1 bit)
- L4_obs (in, 1 bit)
- L5_obs (in, 1 bit)
- L6_obs (in, 1 bit)
- L7_obs (in, 1 bit)
- L8_obs (in, 1 bit)
- L9_obs (in, 1 bit)
- L10_obs (in, 1 bit)
- L11_obs (in, 1 bit)
- L12_obs (in, 1 bit)
- L13_obs (in, 1 bit)
- L14_obs (in, 1 bit)
- L15_obs (in, 1 bit)
- Result_A_obs (in, 16 bits)
- Result_B_obs (in, 16 bits)
- seg7_obs (in, 8 bits)
- sysclk_i (in, 1 bit)
- rst_in (in, 1 bit)
- S0_sti (out, 1 bit)
- S1_sti (out, 1 bit)
- S2_sti (out, 1 bit)
- S3_sti (out, 1 bit)
- S4_sti (out, 1 bit)
- S5_sti (out, 1 bit)
- S6_sti (out, 1 bit)
- S7_sti (out, 1 bit)
- S8_sti (out, 1 bit)
- S9_sti (out, 1 bit)
- S10_sti (out, 1 bit)
- S11_sti (out, 1 bit)
- S12_sti (out, 1 bit)
- S13_sti (out, 1 bit)
- S14_sti (out, 1 bit)
- S15_sti (out, 1 bit)
- Val_A_sti (out, 16 bits)
- Val_B_sti (out, 16 bits)
- rst_o (out, 1 bit)
| TCL | Interface to a Tcl/Tk script using the REDS console pin set. | before 2.13.9 | no | this row |
|---|
TCL genericJava class TclGeneric, saved in files as library TCL. - horloge_i (in, 1 bit)
- val_i (in, 4 bits)
- max_o (out, 1 bit)
- cpt_o (out, 4 bits)
| TCL | Interface to a Tcl/Tk script with pins defined by a VHDL entity. | before 2.13.9 | no | this row |
|---|
D Flip-FlopJava class DFlipFlop, saved in files as library Memory. - in port (in, 1 bit)
- Clock: Clock: state updates on trigger (in, 1 bit)
- Current flip-flop state (out, 1 bit)
- Complement of current flip-flop state (out, 1 bit)
- Clear: Clear: When 1, pin state to 0 asynchronously (in, 1 bit)
- Preset: Preset: When 1, pin state to 1 asynchronously (in, 1 bit)
The default instance has 6 ports in 5.0.0 and 7 in 2.7.1. | Memory | Stores its D input on the clock edge. | before 2.13.9 | yes | Flip-flops and latches |
|---|
T Flip-FlopJava class TFlipFlop, saved in files as library Memory. - in port (in, 1 bit)
- Clock: Clock: state updates on trigger (in, 1 bit)
- Current flip-flop state (out, 1 bit)
- Complement of current flip-flop state (out, 1 bit)
- Clear: Clear: When 1, pin state to 0 asynchronously (in, 1 bit)
- Preset: Preset: When 1, pin state to 1 asynchronously (in, 1 bit)
The default instance has 6 ports in 5.0.0 and 7 in 2.7.1. | Memory | Toggles its state on the clock edge when T is 1. | before 2.13.9 | yes | Flip-flops and latches |
|---|
J-K Flip-FlopJava class JKFlipFlop, saved in files as library Memory. - in port (in, 1 bit)
- in port (in, 1 bit)
- Clock: Clock: state updates on trigger (in, 1 bit)
- Current flip-flop state (out, 1 bit)
- Complement of current flip-flop state (out, 1 bit)
- Clear: Clear: When 1, pin state to 0 asynchronously (in, 1 bit)
- Preset: Preset: When 1, pin state to 1 asynchronously (in, 1 bit)
The default instance has 7 ports in 5.0.0 and 8 in 2.7.1. | Memory | Set/reset/toggle flip-flop with J and K inputs. | before 2.13.9 | yes | Flip-flops and latches |
|---|
S-R Flip-FlopJava class SRFlipFlop, saved in files as library Memory. - in port (in, 1 bit)
- in port (in, 1 bit)
- Clock: Clock: state updates on trigger (in, 1 bit)
- Current flip-flop state (out, 1 bit)
- Complement of current flip-flop state (out, 1 bit)
- Clear: Clear: When 1, pin state to 0 asynchronously (in, 1 bit)
- Preset: Preset: When 1, pin state to 1 asynchronously (in, 1 bit)
The default instance has 7 ports in 5.0.0 and 8 in 2.7.1. | Memory | Set/reset flip-flop. | before 2.13.9 | yes | Flip-flops and latches |
|---|
RegisterJava class Register, saved in files as library Memory. - Output: Output: register’s current value (out, 8 bits)
- Data: Data: value stored on clock trigger (in, 8 bits)
- Clock: Clock: value updates on trigger (in, 1 bit)
- Clear: Clear: When 1, pin value to 0 asynchronously (in, 1 bit)
- Enable: Enable: When 0, clock triggers are ineffective (in, 1 bit)
| Memory | Multi-bit storage loaded on a clock edge. | before 2.13.9 | yes | Registers, shift registers, register files |
|---|
CounterJava class Counter, saved in files as library Memory. - Output: Output: current value of counter (out, 8 bits)
- Data: Data: value to load into counter (in, 8 bits)
- Clock: Clock: value may update on trigger (in, 1 bit)
- Clear: Clear: when 1, resets to 0 asynchronously (in, 1 bit)
- Load: Load: when 1, loads from data input (in, 1 bit)
- Up Down: Up Down: when 1, counter increments, when 0, counter decrements (in, 1 bit)
- Enable: Enable: when 1, counter increments or decrements (in, 1 bit)
- Carry: Carry: is 1 when value reaches maximum (minimum if decrementing) (out, 1 bit)
The default instance has 8 ports in 5.0.0 and 7 in 2.7.1. | Memory | Counts up or down with load, clear and configurable overflow action. | before 2.13.9 | yes | Counter |
|---|
Shift RegisterJava class ShiftRegister, saved in files as library Memory. - Input: Input: value to be shifted into first stage (in, 1 bit)
- Shift: Shift: shift is disabled when 0 (in, 1 bit)
- Clock: Clock: values may update on trigger (in, 1 bit)
- Clear: Clear: when 1, resets all to 0 asynchronously (in, 1 bit)
- Output: Output: is content of last stage (out, 1 bit)
- Load: Load: when 1 (with shift = 0), all stages load from inputs (in, 1 bit)
- in port (in, 1 bit)
- out port (out, 1 bit)
- in port (in, 1 bit)
- out port (out, 1 bit)
- in port (in, 1 bit)
- out port (out, 1 bit)
- in port (in, 1 bit)
- out port (out, 1 bit)
- in port (in, 1 bit)
- out port (out, 1 bit)
- in port (in, 1 bit)
- out port (out, 1 bit)
- in port (in, 1 bit)
- out port (out, 1 bit)
- in port (in, 1 bit)
The default instance has 21 ports in 5.0.0 and 22 in 2.7.1. | Memory | Shifts data through a chain of stages each clock, with optional parallel load. | before 2.13.9 | yes | Registers, shift registers, register files |
|---|
Random GeneratorJava class Random, saved in files as library Memory. - Output: Output: current number in sequence (out, 8 bits)
- Clock: Clock: value may update on trigger (in, 1 bit)
- Enable: Enable: steps to next in sequence on clock trigger (in, 1 bit)
- Clear: Clear: When 1, resets to initial seed asynchronously (in, 1 bit)
| Memory | Produces pseudo-random values on each clock (xoshiro256++ since 5.0.0). | before 2.13.9 | yes | this row |
|---|
RAMJava class Ram, saved in files as library Memory. - Address: Address: location accessed in memory (in, 8 bits)
- Data: Data: value loaded from address (out, 8 bits)
- Input: Input: value to be stored at address (in, 8 bits)
- Load: Load: if 1, load memory to output (in, 1 bit)
- Store: Store: if 1, store input to memory (in, 1 bit)
- Clock: Clock: memory value updates on rise from 0 to 1 (in, 1 bit)
| Memory | Read/write memory with editable contents and several bus layouts. | before 2.13.9 | yes | RAM |
|---|
ROMJava class Rom, saved in files as library Memory. - Address: Address: location accessed in memory (in, 8 bits)
- Data: Data: value loaded from address (out, 8 bits)
The default instance has 2 ports in 5.0.0 and 3 in 2.7.1. | Memory | Read-only memory whose contents are stored in the .circ file. | before 2.13.9 | yes | ROM and loading memory contents |
|---|
Dual Port RAMJava class DualRam, saved in files as library Memory. - Address: Address: location accessed in memory (in, 8 bits)
- Address: Address: location accessed in memory (in, 8 bits)
- Data: Data: value loaded from address+0 (out, 8 bits)
- Data: Data: value loaded from address+1 (out, 8 bits)
- Input: Input: value to be stored at address+0 (in, 8 bits)
- Input: Input: value to be stored at address+1 (in, 8 bits)
- Load: Load: if 1, load memory to output (in, 1 bit)
- Load: Load: if 1, load memory to output (in, 1 bit)
- Store: Store: if 1, store input to memory (in, 1 bit)
- Store: Store: if 1, store input to memory (in, 1 bit)
- Clock: Clock: memory value updates on rise from 0 to 1 (in, 1 bit)
- Clock: Clock: memory value updates on rise from 0 to 1 (in, 1 bit)
| Memory | RAM with two independent access ports. | 4.1.0 | no | this row |
|---|
Risc V IM simulatorJava class Rv32imRiscV, saved in files as library Soc. - Reset input (in, 1 bit)
- Clock input (in, 1 bit)
| System On a Chip | Simulated RV32IM RISC-V processor core for SoC designs. | 3.3.0 | no | this row |
|---|
Nios2s simulatorJava class Nios2, saved in files as library Soc. - Clock input (in, 1 bit)
- Reset input (in, 1 bit)
- Data A (out, 32 bits)
- Data B (out, 32 bits)
- Start (out, 1 bit)
- N (out, 8 bits)
- A (out, 5 bits)
- Read Ra (out, 1 bit)
- B (out, 5 bits)
- Read Rb (out, 1 bit)
- C (out, 5 bits)
- Write Rc (out, 1 bit)
- Result (in, 32 bits)
- Done (in, 1 bit)
| System On a Chip | Simulated Intel/Altera Nios II-style processor core. | 3.3.0 | no | this row |
|---|
SoC bus simulatorJava class SocBus, saved in files as library Soc. | System On a Chip | Shared bus connecting SoC processors, memories and peripherals. | 3.3.0 | no | this row |
|---|
Memory simulatorJava class SocMemory, saved in files as library Soc. | System On a Chip | Memory block for the SoC bus. | 3.3.0 | no | this row |
|---|
Parallel input/output expanderJava class SocPio, saved in files as library Soc. - Reset input (in, 1 bit)
- Input bit 0 (in, 1 bit)
| System On a Chip | Parallel I/O peripheral on the SoC bus. | 3.3.0 | no | this row |
|---|
VGA screenJava class SocVga, saved in files as library Soc. | System On a Chip | VGA-style display peripheral on the SoC bus. | 3.3.0 | no | this row |
|---|
DMA engineJava class SocDma, saved in files as library Soc. - Reset (in, 1 bit)
- Clock (in, 1 bit)
- IRQ (out, 1 bit)
| System On a Chip | Memory-to-memory copy engine on the SoC bus (added 4.1.0). | 4.1.0 | no | this row |
|---|
JTAG UARTJava class JtagUart, saved in files as library Soc. - Clock input (in, 1 bit)
- Reset input (in, 1 bit)
- Irq output (out, 1 bit)
- Keyboard read enable (out, 1 bit)
- Clear keyboard (out, 1 bit)
- Keyboard data available (in, 1 bit)
- Keyboard data (in, 7 bits)
- TTY data (out, 7 bits)
- TTY write data (out, 1 bit)
- TTY clear (out, 1 bit)
| System On a Chip | Character I/O peripheral modelled on the JTAG UART. | 3.3.0 | no | this row |
|---|
RGB VideoJava class Video, saved in files as library I/O. - in port (in, 1 bit)
- in port (in, 1 bit)
- in port (in, 1 bit)
- in port (in, 7 bits)
- in port (in, 7 bits)
- in port (in, 24 bits)
| Input/Output | Pixel display / framebuffer the circuit writes colours into. | 3.3.0 | no | Keyboard, TTY, LED matrix and video |
|---|